manualshive.com logo in svg

Motorola MTR2000, Инструкция по установке и эксплуатации

Поделиться
Скачать
Motorola MTR2000 Скачать руководство пользователя страница 39

Installation

12

68P81096E37-N

06/28/05

This section describes the procedures to unpack and mechanically install the station equipment.  A variety of 
mounting methods are possible, depending on whether a cabinet or rack (if any) has been selected to house the 
station(s).  Installation procedures are provided for each of the cabinet and rack types, as well as the slide rail. 

Be sure to observe proper electrostatic discharge precautions if modules 
must be removed from the station.  

Unpacking Equipment

Introduction

Station equipment packing methods vary depending upon the type of op-
tional rack or cabinet selected by the customer.  Unpacking procedures for 
these various methods are provided in the following paragraphs.

The equipment must be immediately inspected for damage after un-
packing, and a report of the extent of any damage made to the transpor-
tation company and to Motorola.  

Unpacking Stations

The station is shipped in a carton, cushioned by four plastic inserts at the 
corners of the carton. 

Improper handling of the station may cause personal injury or damage 
to the station.  DO NOT pick up the station by holding the Preselector 
(if so equipped).  Use the  handles on the front of the station, or the Pow-
er Supply and Power Amplifier casings when picking up the station.  

Front Panel – Removal and Replacement

Remove station front panel by inserting a small flat-blade screwdriver into 
one of two access holes at either end of the panel and, by carefully moving 
the handle of the screwdriver away from the center, release the front panel 
locking clip from the chassis and pull away the panel

.  

Replace station front panel by inserting one of the front panel locking clips 
into corresponding latch on the station housing, and carefully pressing the 
panel on the opposite side until the second locking clip snaps into place. 

 

2

MECHANICAL INSTALLATION

STOP

IMPORTANT

STOP

IMPORTANT

STOP

WARNING

Содержание MTR2000
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды