Motorola MTR2000 Скачать руководство пользователя страница 72

Страница: 72 / 79

Installation

68P81096E37-N

06/28/05

A major failure renders the station unusable. These failure could be
caused by one of the following conditions:
-

Rx or Tx synthesizer out of lock

PA failure,

Sharp (i.e., 10dB) rf power cutback,

self test failure

A random flashing of the Station Status LED indicates major failure of
the Station Control Module; since a control module reset turns the LEDs
on.

A minor failure limits the functionality of the station. These failures could
be caused by one of the following conditions:
-

ac source power failure

exciter or receiver analog metering voltage degradation

wireline loopback failure

invalid local channel selection

Boot mode is the mode the station is in during the loading of software into
the station’s Flash memory.

Service mode is the mode the station is in during normal maintenance and
service periods. These modes include the following conditions:
-

Intercom

PL Disable

Access Disable

Failsoft Disable

Power Control Disable

Service PTT

The Radio Service Software (RSS) can be used to determine which failure
or service modes are active.

Service mode indicates that the station is not fully functional.

RX Active

LED

This

RX Active

LED indicates the following:

This LED is lit when receive activation criteria (user defined) are satisfied;
i.e., the radio is unsquelched.

CAUTION

LED Color

LED State

Indicates that the…

Green

Receiver is active.

Содержание MTR2000
















































































Результаты поиска

Содержание MTR2000

Отзывы:

Бренды по названию

Популярные бренды

Motorola MTR2000, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MTR2000

Отзывы:

Бренды по названию

Популярные бренды