manualshive.com logo in svg

Motorola MTR2000, Инструкция по установке и эксплуатации

Поделиться
Скачать
Motorola MTR2000 Скачать руководство пользователя страница 70

Installation

68P81096E37-N

43

06/28/05

After the station equipment has been mechanically installed and all electrical connections have been made, power 
may now be applied and the station checked for proper operation.   

Applying Power

Before applying power to the station, make sure all boards are securely 
seated in the appropriate connectors on the backplane and that all rf cables 
are securely connected.

Turn ON the circuit breaker controlling the ac outlet that is supplying 
power to the station Power Supply Module, or switch on the DC-supply 
to a station with a DC-only Power Supply Module.

Changing Fuse

To replace the station fuse:

1.

Turn off station power at source (e.g., ac breaker).

2.

Remove fuse cover plate located on the backplane shield by unscrew-
ing one M4 screw.

3.

Pull defective fuse carefully with small needle nose pliers.

4.

Replace new fuse (part # 6583049X16) carefully with small needle 
nose pliers.

For continued protection of the station against risk of fire, replace 
the fuse only with the same type and rating of fuse.

5.

Restore power to the station.

5

POST INSTALLATION CHECKLIST

CAUTION

!

Содержание MTR2000
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды