Motorola DigitalDNA ColdFire MCF5272 Скачать руководство пользователя страница 175 | Manualshive

Страница: 175 / 550

background image

Chapter 7. Interrupt Controller

7-3

Interrupt Controller Registers

All external interrupt inputs are edge sensitive, with the active edge being programmable
through PITR. An interrupt must remain asserted for at least three consecutive rising edges
of CPU_ExtCLK to be considered valid. The priority level of each interrupt source is
programmed through the ICRs.

The MCF5272 does not support auto-vectored interrupts. Interrupt service routines for all
interrupts should have vectors in the user-defined interrupt region of the vector table
(vectors 64–255). The location of these vectors is programmable through the PIVR. For
more information on the servicing of interrupts, see Chapter 2, “ColdFire Core.” Pending
interrupts from external sources (INT[6:1]) can be cleared using the ICRs.

For an interrupt to be successfully processed, stack RAM must be available. A
programmable chip select is often used for the RAM, in which case, the RAM is not
immediately available at startup. Thus, no interrupts are recognized until PIVR is
initialized. The RAM chip select and system stack should be set up before this initialization.

If more than one interrupt source has the same interrupt priority level (IPL), the interrupt
controller daisy chains the interrupts with the priority order following the bit placement in
the PIWR, with INT1 having the highest priority and SWTO having the lowest priority, as
shown in Figure 7-8.

7.2.1 Interrupt Controller Registers

This section describes the registers associated with the interrupt controller. Table 7-2 gives
the nomenclature used for the interrupt and power management registers.

0x030

Interrupt source register (ISR) [p. 7-6]

0x034

Programmable interrupt transition register (PITR) [p. 7-8]

0x038

Programmable interrupt wakeup register (PIWR) [p. 7-9]

0x03C

Reserved

Programmable interrupt

vector register (PIVR)

Table 7-2. Interrupt and Power Management Register Mnemonics

Mnemonic or Portion Thereof

Description

INT1, INT2, INT3, INT4, INT5, INT6

External interrupt signals 1–6.

TMR1, TMR2, TMR3, TMR4

Timers 1–4 from timer module

USB0, USB1, USB2, USB3, USB4, USB5,
USB6, USB7

USB endpoint 0–7

UART1, UART2

UART1, UART2 modules

PLIP

PLIC 2-KHz periodic interrupt, 2B+D data

PLIA

PLIC asynchronous and maintenance channels interrupt

DMA

DMA controller interrupt

Table 7-1. Interrupt Controller Registers

«
...
173
174
175
176
177
...
»

Содержание DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DigitalDNA ColdFire MCF5272

Бренд: National Instruments Страницы: 5

Бренд: National Instruments Страницы: 76

SCSI PC Card REX-9530V

Бренд: Ratoc Systems Страницы: 30

Бренд: Zonet Страницы: 2

Бренд: Patton electronics Страницы: 145

DAS-1800HR Series

Бренд: Keithley Страницы: 139

POD-51EH-C541U-12

Бренд: IceTech Страницы: 8

Бренд: Intel Страницы: 154

Бренд: ExtraHop Страницы: 3

Safeguard for Privileged Sessions 3000

Бренд: One Identity Страницы: 37

Бренд: Z3 Technology Страницы: 83

Бренд: Lattice Semiconductor Страницы: 25

GigaVUE H Series

Бренд: Gigamon Страницы: 55

Бренд: EK-Quantum Страницы: 18

Бренд: Jennic Страницы: 14

Бренд: Alcatel-Lucent Страницы: 8

Бренд: Fujitsu Страницы: 7

Бренд: Fujitsu Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды