Motorola DigitalDNA ColdFire MCF5272 Скачать руководство пользователя страница 387 | Manualshive

Страница: 387 / 550

background image

Chapter 16. UART Modules

16-27

Operation

The two error modes are selected by UMR1n[ERR] as follows:

•

In character mode (UMR1n[ERR] = 0), status is given in the USRn for the character
at the top of the FIFO.

•

In block mode, the USRn shows a logical OR of all characters reaching the top of
the FIFO stack since the last

RESET

ERROR

STATUS

command. Status is updated as

characters reach the top of the FIFO stack. Block mode offers a data-reception speed
advantage where the software overhead of error-checking each character cannot be
tolerated. However, errors are not detected until the check is performed at the end of
an entire message—the faulting character in the block is not identified.

In either mode, reading the USRn does not affect the FIFO. The FIFO is popped only when
the receive buffer is read. The USRn should be read before reading the receive buffer. If all
24 receiver holding registers are full, a new character is held in the receiver shift register
until space is available. However, if a second new character is received, the character in the
receiver shift register is lost, the FIFO is unaffected, and USRn[OE] is set when the receiver
detects the start bit of the new overrunning character.

Visibility into the status of the FIFO is provided by various bits and interrupts, as shown in
Table 16-17.

To support flow control, the receiver can be programmed to automatically negate and assert
RTS, in which case the receiver automatically negates RTS when a valid start bit is detected
and the FIFO stack is full. The receiver asserts RTS when a FIFO position becomes
available; therefore, overrun errors can be prevented by connecting RTS to the CTS input
of the transmitting device.

NOTE:

The receiver can still read characters in the FIFO stack if the
receiver is disabled. If the receiver is reset, the FIFO stack, RTS
control, all receiver status bits, and interrupt requests are reset.
No more characters are received until the receiver is reenabled.

Table 16-17. Receiver FIFO Status Bits

Status Bit

Indicated Condition

Interrupt

USR[FFULL] = 1

All FIFO positions contain data

Yes

USR[RxRDY] = 1

At least one character is available to be read by the CPU.

Yes

USR[RxFIFO] = 1

The programmed level of fullness (UTF[RXS]) has been reached.

Yes

USR[RxFTO] = 1

The receiver FIFO holds unread data, and the FIFO status has not
changed in at least 64 receiver clocks.

Yes

URF[RXS]

Indicates the level of fullness of the receiver FIFO

URF[RXB]

Indicates the number of characters, 0–24, in the receiver FIFO.

«
...
385
386
387
388
389
...
»

Содержание DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DigitalDNA ColdFire MCF5272

Бренд: National Instruments Страницы: 162

Бренд: Zhone Страницы: 1

Бренд: ekwb Страницы: 2

Бренд: ZALMAN Страницы: 22

Бренд: 3Ware Страницы: 4

Бренд: Advantech Страницы: 50

EK-FC750 GTX Series

Бренд: ekwb Страницы: 2

Бренд: ASROCK Страницы: 173

Бренд: Rosewill Страницы: 2

Бренд: Stepper Motor Canada Страницы: 5

Бренд: ADS Technologies Страницы: 1

Бренд: CSL Страницы: 24

Бренд: McIntosh Страницы: 44

AH10EN-5A Series

Бренд: Delta Страницы: 132

Бренд: Comelit Страницы: 140

Quark SoC X1000

Бренд: Galileo Страницы: 20

Бренд: Lucent Technologies Страницы: 7

Бренд: MEN Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды