Motorola DigitalDNA ColdFire MCF5272 Скачать руководство пользователя страница 444 | Manualshive

Страница: 444 / 550

background image

19-30

MCF5272 User’s Manual

Physical Layer Interface Controller TDM Ports

19.15.1.3 Data Clock (DCL0/URT1_CLK)

IDL mode: This pin is the clock used to clock data in and out of DIN0 and DOUT0 for IDL
port 0. Data is clocked into DIN0 on the falling edge and clocked out of DOUT0 on the
rising edge of DCL0.

GCI mode: This pin is used to clock data in and out of DIN0 and DOUT0 for GCI port 0.
DCL0 is twice the bit rate (two clocks per data bit).

UART1: URT1_CLK provides a clock input which can be the baud rate clock.

19.15.1.4 Serial Data Input (DIN0/URT1_RxD)

IDL mode: The DIN0 input is for clocking data into IDL port 0. Data is clocked into DIN0
on the falling edge of DCL0.

GCI mode: The DIN0 input is for clocking data into GCI port 0. DCL0 is twice the bit rate
(two clocks per data bit).

UART1: URT1_RxD is the receiver serial data input for the UART1 module. Data received
on this pin is sampled on the rising edge of the serial clock source with the least significant
bit first. When the UART1 clock is stopped for power-down mode, any transition on this
pin restarts it.

19.15.1.5 UART1 CTS (URT1_CTS/QSPI_CS2)

UART1: URT1_CTS is the clear-to-send input indicating to the UART1 module that it can
begin data transmission.

QSPI mode: This output pin provides a QSPI peripheral chip select, QSPI_CS2, when in
Master mode. QSPI_CS2 can be programmed to be active high or low.

19.15.1.6 UART1 RTS (URT1_RTS/INT5)

Interrupt mode: This pin can be used as INT5.

UART1: The URT1_RTS output is an automatic request to send output from the UART1
module. It can be configured to be asserted and negated as a function of the RxFIFO level.

19.15.1.7 Serial Data Output (DOUT0/URT1_TxD)

IDL mode: The DOUT0 output is for clocking data out of IDL port 0. Data is clocked out
of DOUT0 on the rising edge of DCL0.

GCI mode: The DOUT0 output is for clocking data out of GCI port 0. DCL0 is twice the
bit rate (two clocks per data bit).

UART1: URT1_TxD is the transmitter serial data output for the UART1 module. The
output is held high ('mark' condition) when the transmitter is disabled, idle, or operating in
the local loop back mode. Data is shifted out, least significant bit first, on this pin at the
falling edge of the serial clock source.

«
...
442
443
444
445
446
...
»

Содержание DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DigitalDNA ColdFire MCF5272

ShareCenter DNS-320L

Бренд: D-Link Страницы: 4

Бренд: LaCie Страницы: 44

LaCie Ethernet Disk

Бренд: LaCie Страницы: 2

SATA II ExpressCard 34

Бренд: LaCie Страницы: 2

12big Rack Fibre 8

Бренд: LaCie Страницы: 9

Бренд: Waves Страницы: 41

Digital Encoder Plus

Бренд: IDT Страницы: 98

Бренд: Glacier Страницы: 2

Бренд: Paradyne Страницы: 6

REJ06B0734-0100

Бренд: Renesas Страницы: 19

Бренд: Intel Страницы: 958

Бренд: PairGain Страницы: 80

Бренд: Bailey Страницы: 33

Бренд: Sony Ericsson Страницы: 93

Бренд: DFRobot Страницы: 30

Бренд: Navitar Страницы: 1

Network Scanning Unit A

Бренд: Ricoh Страницы: 206

Бренд: Kontron Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды