manualshive.com logo in svg

Morningstar TS-MPPT-60-600V-48-DB-TR, Инструкция по установке, эксплуатации и обслуживанию, Страница: 9 / 45

Поделиться
Скачать
Morningstar TS-MPPT-60-600V-48-DB-TR Скачать руководство пользователя страница 9

17

 

 TriStar MPPT-600V-TR Operator's Manual

16

 Getting Started

Meter Hub (HUB-1)

A Morningstar MeterBus

TM

 network with multiple controllers requires a Meter Hub for electrical 

isolation. The HUB-1 allows communication between MeterBus

TM

 compatible Morningstar prod-

ucts, including the TS-MPPT-600V-TR controller. DIN rail compatible. See section 5.2 for more 

details.

Relay Driver (RD-1)

The Relay Driver

TM

 accessory enables the TS-MPPT-600V-TR to control external devices. Four 

(4) relay control ports can be configured (in various combinations) to perform the following tasks:

•  generator control (2-, 3-, and 4-wire configurations)
•  dry contacts for alarms and other signals
•  advanced load control
•  vent fan control
•  DIN rail compatible or surface mount

For more information on the Relay Driver, visit our website at www.morningstarcorp.com or 

inquire with your local Morningstar dealer.

EIA-485 / RS-232 Communications Adapter (RSC-1)

Connect one or more TS-MPPT-600V-TR controllers to a PC or to other serial devices using the 

EIA-485 adapter. The adapter converts an RS-232 serial interface to EIA-485 compliant bus 

signals. An LED shows network activity and errors. DIN rail compatible.

     Ethernet Communications Adapter (EMC-1)

This product is an Ethernet gateway that provides web monitoring services, a Modbus TCP/IP 

server, and a local web page server. End users can collect information about their off-grid PV 

system remotely.  One EMC-1 supports all products with MeterBus ports by bridging MODBUS 

TCP/IP requests to serve LiveView pages for each product.

USB Communications Adapter (UMC-1)

A modular unit that uses a USB-B plug, usually from a USB A-B computer cable, and an RJ-11 

plug to connect with a Morningstar controller's MeterBus port, for monitoring and programming 

using MSView PC software.

19 - Solar Terminal Bridge (yellow)

Isolates high voltage PV wiring from low voltage wiring area

20 - (+) and (-) Solar Power Terminals (pre-wired)

(+) and (-) solar terminal connection points

Optional TS-MPPT-60-600V-48-DB-TR-GFPD Box

21 - Breaker Mounting Plate (removable)

Pre-wired and mounted GFPD sensor and breaker assembly

22 - Ganged Ground-fault Breakers

(+) and (-) leg ground-fault interruption breakers 

  

23 - (+) and (-) Solar Breaker Post Connections [(pre-wired),(underside)]

Connection points for (+) and (-) solar wires 

24 - Solar Wiring Aperture

Sensing opening for GFPD control

25 - Auxilliary DIN Rail Mount

Available for DIN mountable equipment

26 - Grounding Terminal Block

A chassis terminal for system grounding

27 - Test / Reset Button

Performs testing and reset functions

28 -  Bi-Color LED

Indicates various fault and alarm conditions

29 -  GFPD Control and Power Terminals

Terminal connections for GFPD signals and power.

2.5 Optional Accessories

The accessories described below are available for purchase separately from your authorized 

Morningstar dealer.  Please see the individual product manuals for installation and operation 

details.

TriStar Meter 2-600V; TriStar Remote Meter 2 (Models: TS-M-2-600V; TS-

RM-2)

The TS-M-2-600V

 

mounts directly on the TS-MPPT-600V-TR controller, replacing the blank 

meter cover on the wiring box lid. The TS-RM-2 can be flush mounted in a wall or into a standard 

duplex (2-gang) electrical box. A 2 x 16 character display shows system operating information, 

error indications, and self-diagnostic information. Four (4) buttons make navigating the meter 

menus easy. 
TriStar meters connect to the RJ- 11 MeterBus

TM

 port on the TS-MPPT-600V-TR.

  

One (1) meter 

can display select full system information when multiple TS-MPPT-600V-TR or other TriStar con-

trollers are connected via a MeterBus

TM  

network. 

Содержание TS-MPPT-60-600V-48-DB-TR














































Отзывы:

Нет отзывов