Morningstar TS-MPPT-60-600V-48-DB-TR Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 45

Morningstar TS-MPPT-60-600V-48-DB-TR Скачать руководство пользователя страница 11

21

TriStar MPPT-600V-TR Operator's Manual

20

Installation

High and Low Voltage Wiring Positions

-

TS-MPPT-600V-TR

Figure 3-1. TS-MPPT-600V-TR / GFPD high and low voltage wiring zones (shaded areas)

600V wiring below

the removable

Wiring Divider

(divider removed)

Low voltage wiring

above the Wiring

Divider

(divider in place)

3.3 Conduit Knock-Outs and Wire Routing

Knock-outs are provided for routing cables through conduit or wire glands. Table 3-1 details the

knockout sizes and quantity provided on the TS-MPPT-600V-TR wiring box. Knockout placement

dimensions are on the inside front cover. Figures 3-2 and 3-3 show knock-out types.

The TS-MPPT-600V-TR wiring box provides continuous and separate paths for high

voltage (solar) and low voltage (battery & COM) wiring routing. These allow wiring to pass be-

tween TS-MPPT-600V-TR controllers that are mounted side-by-side without the need for exter-

nal conduit tubing. Table 3-1 identifies the pass-through knock-outs which may be used for this

purpose. Figure 3-6 shows the routing of the high voltage and low voltage wiring paths.

3

8

7

10

4

9

2

2

6

5

5

1

1

1

3

6

11

Figure 3-2. Knock-outs, left , right and back views

«
...
9
10
11
12
13
...
»

Содержание TS-MPPT-60-600V-48-DB-TR














































Отзывы:

Нет отзывов