manualshive.com logo in svg

Morningstar TS-MPPT-60-600V-48-DB-TR, Инструкция по установке, эксплуатации и обслуживанию, Страница: 35 / 45

Поделиться
Скачать
Morningstar TS-MPPT-60-600V-48-DB-TR Скачать руководство пользователя страница 35

68

 Testing and Troubleshooting

Problem: 

Cannot connect to the controller via Ethernet

Solution: 

See the Morningstar Product Connectivity Manual, available on our website: 

http://www.morningstarcorp.com/wp-content/uploads/2014/02/MS-Comm-Document-2010.pdf                    

GFPD-600V

      

Test Button Uses:

 

The test button can be used for three purposes: 

 

1. With the GFPD-600V in normal mode, pressing the test button conducts a system test that opens  

 

the breaker, shows a red solid LED, and sounds the buzzer;

 

2. When a ground-fault error has occurred, pressing the test button resets the GFPD-600V to the    

 normal 

condition;

 

3. When a wiring error / open breaker alarm has occurred, pressing the test button resets the  

 

 

GFPD-600V to the normal condition.  

   

  

Faults and Corrections:

 

♦ When a ground-fault error has occurred, push the test button and then close the breaker to  

 

 

resume normal operation.  Have a qualified technician investigate the ground-fault cause. 

 

♦ When a wiring error / open breaker alarm has occurred, correct wiring error and/or close breaker.   

 

Push the test button to resume normal operation.

 

♦ 

When the low battery voltage threshold of nine volts is reached, the buzzer will sound. To   

 

 

resume normal operation, re-charge or replace the battery powering the GFPD-600V.

 

♦ 

Push the test button to perform a system test. Close the breaker to resume normal operation.       

 

♦ 

A critical fault indicates a hardware malfunction.  Please contact Morningstar for instructions. 

 

♦

 If previous trouble-shooting does not correct the problem, re-start the unit by removing in-line    

 

source fuse, and re-installing.

69

TriStar MPPT 600V-TR Operator’s Manual

Your TS-MPPT-600V-TR will provide years of reliable and trouble-free service. The unit contains 

no electromechanical parts such as relays or cooling fans that can wear out and fail.  Additionally, 

there are no user-serviceable parts inside the controller. 

7.1  Important Safety Instructions

          

SAVE THESE INSTRUCTIONS.

This manual contains important safety, installation and operating instructions for the 

TS-MPPT-600V-TR solar controller.  The following symbols are used throughout this manual to 

indicate potentially dangerous conditions or mark important safety instructions:

  

 

WARNING:  

Indicates a potentially dangerous condition.  Use extreme caution 

when performing this task.

!

CAUTION:  

Indicates a critical procedure for safe and proper operation of the 

controller.

NOTE:  

Indicates a procedure or function that is important for the safe and 

proper operation of the controller.

AVERTISSEMENT :  

Indique une condition potentiellement dangereuse.  Faites preuve 

d’une prudence extrême lors de la réalisation de cette tâche.

!

PRUDENCE :  

Indique une procédure critique pour l’utilisation sûre et correcte du 

contrôleur.

REMARQUE :  

Indique une procédure ou fonction importante pour l’utilisation sûre et 

correcte du contrôleur.

Safety Information

•  Read all of the instructions and cautions in the manual before beginning installation.
•  There are no user serviceable parts inside the TS-MPPT-600V-TR.  Do not disassemble 

or attempt to repair the controller.

              

WARNING:

  

RISK OF ELECTRICAL SHOCK.

  

             

NO  POWER OR ACCESSORY TERMINALS ARE ELECTRICALLY ISOLATED FROM 

DC INPUT, AND MAY BE ENERGIZED WITH HAZARDOUS SOLAR VOLTAGE.  UNDER CER-

TAIN FAULT CONDITIONS, BATTERY COULD BECOME OVER-CHARGED.  TEST BETWEEN 

ALL TERMINALS AND GROUND BEFORE TOUCHING.

 

 Maintenance and Service

7.0

Содержание TS-MPPT-60-600V-48-DB-TR














































Отзывы:

Нет отзывов