Morningstar TS-MPPT-60-600V-48-DB-TR Скачать руководство пользователя страница 19

Страница: 19 / 45

TriStar MPPT-600V-TR Operator's Manual

Installation

If a TriStar meter is installed, check the “TriStar Settings” to confirm the Voltage Sense and the

RTS (if installed) are both present and detected by the controller. MSView

PC software can

also be used to confirm the voltage sense is working correctly.

Step 9 - Adjust Settings Switches

Switch 1: Future Use

Select the charging source that will be connected to the TS-MPPT-600V-TR.

Mode

Switch 1

Solar Charging

OFF

Future Use

Switch 2: Not Used (OFF)

Switch 3: Charging Mode

Charging Mode

Switch 3

Normal 48V

OFF

Custom Multiplier*

Allows for nominal charging voltages of 24, 36, or 60V. Battery compatibility must be verified.

Switches 4, 5, & 6: Battery Charging Settings

It is important to select the battery type that matches the system battery to ensure proper charg-

ing and long battery life. Refer to the specifications provided by the battery manufacturer and

choose a setting that best fits the recommended charging profile.

Settings

Switches

4 - 5 - 6

Battery

Type

Absorp.

Stage

(Volts)

Float

Stage

(Volts)

Equalize

Stage

(Volts)

Equalize

Interval

(Days)

off-off-off

1 - Gel

56.00

54.80

off-off-on

2 - Sealed*

56.60

54.80

57.60

off-on-off

3 - Sealed*

57.20

54.80

58.40

off-on-on 4 - AGM/Flooded

57.60

54.80

60.40

on-off-off

5 - Flooded

58.40

54.00

61.20

on-off-on

6 - Flooded

58.80

54.00

61.60

on-on-off

7 - L-16

61.60

53.60

64.00

on-on-on

8 - Custom

Custom

* “Sealed” battery type includes gel and AGM batteries

All settings are for 48 volt nominal systems. Descriptions of battery type and stages are provided

below. See section 4.2 for full details.

Battery Type - The most common battery type associated with the specified charging settings.

Absorption Stage - This stage limits input current so that the Absorption voltage is maintained.

As the battery becomes more charged, the charging current continues to taper down until the

battery is fully charged.

Float Stage - When the battery is fully charged, the charging voltage will be reduced to the Float

voltage setting.

Equalize Stage - During an equalization cycle, the charging voltage will be held constant at the

specified voltage setting.

Equalize Interval - The number of days between equalization charges when the controller is

configured for automatic equalizations (settings switch 7).

Switch 7: Battery Equalization

Choose between manual and automatic battery equalization charging. In the manual

equalization setting, an equalization will only occur when manually started with the pushbutton or

when requested from the equalize menu on the TriStar meter. Automatic equalization will occur

according to the battery program specified by settings switches 4, 5, & 6 in the previous step.

In both settings (auto and manual), the push-button can be used to start and stop battery

equalization. If the selected battery charging setting does not have an equalization stage, an

equalization will never occur, even if requested manually.

Equalize

Switch 7

manual

OFF

automatic

Switch 8: Ethernet Security

The Ethernet Security switch enables or disables configuration of the TS-MPPT-600V-TR set-

tings through the Ethernet connection. When switch 8 is set to

disabled

, write commands to the

TS-MPPT-600V-TR custom memory are not allowed through the Ethernet connection. This safety

feature will prevent unintended changes to custom settings, but it is not a substitute for proper

network security.

Configuration via TCP/IP

Switch 8

disabled

OFF

enabled

NOTE:

Adjustment of network settings and custom set-points is always enabled via the RS-232 and EIA-

485 connections. The Ethernet Security switch only enables/disables remote configuration via

TCP/IP.

Содержание TS-MPPT-60-600V-48-DB-TR














































Результаты поиска

Содержание TS-MPPT-60-600V-48-DB-TR

Отзывы:

Morningstar TS-MPPT-60-600V-48-DB-TR, Инструкция по установке, эксплуатации и обслуживанию, Страница: 19 / 45

Результаты поиска

Содержание TS-MPPT-60-600V-48-DB-TR

Отзывы: