Morningstar TS-MPPT-60-600V-48-DB-TR Скачать руководство пользователя страница 27

Страница: 27 / 45

TriStar MPPT-600V-TR Operator's Manual

Operation

4.6 LED Indications & Audible Warnings

Valuable information is provided by the three LEDs visible through the front cover. Although

there are many different LED indications, they have similar patterns to make it easier to interpret

each LED display. Consider as three groups of indications: General Transitions // Battery Status

// Faults & Alarms.

LED Display Explanation

G = green LED is lit

Y / R = yellow LED is lit, then red LED is lit

G+Y = Green and Yellow are both lit at the same time

G+Y / R = Green & Yellow both lit, then Red is lit alone

Sequencing LED patterns (faults) repeat until the fault is cleared

General Transitions

• Controller start-up

G / Y / R (one cycle)

• Equalize request start

G+Y+R / G+Y+R / G / G

• Equalize cancelled

G+Y+R / G+Y+R / R / R

• Battery service is required*

all 3 LEDs blinking until service is reset

*battery service notification is only enabled in custom settings

Battery Status

• General state-of-charge

see battery SOC indications below

• Absorption state

G blinking (½ second on / ½ second off)

• Equalization state

G fast blink (2 to 3 times per second)

• Float state

G slow blink (1 second on / 1 second off)

Faults & Alarms

• Over-temperature

Y / R sequencing

• High voltage disconnect

G / R sequencing

• DIP switch fault

R / Y / G sequencing

• Self-test faults

R / Y / G sequencing

• Remote Temperature Sensor (RTS)

G+Y / Y+R sequencing

• Battery voltage sense

G+Y / Y+R sequencing

• Solar Over-Current

Y + R / G sequencing

Battery State-of-Charge LED Indications

80% to 95% SOC

G+Y

60% to 80% SOC

35% to 60% SOC

Y+R

0% to 35% SOC

battery is discharging

Refer to the Specifications (Section 9.0) for the State-of-Charge voltages.

Note that because these State-of-Charge LED displays are for all battery types and system de-

signs, they are only approximate indications of the battery charge state.

Ethernet Jack Indications

In addition to the SOC LEDs, two (2) small LEDs can be found on the Ethernet RJ-45 jack inside

the wiring box. These LEDs indicate the LAN/WAN network link and activity status as follows:

Condition

Yellow LED

Green LED

Network Connection OK

OFF

Network Activity

Blinking

Error

OFF

GFPD-600V LED Indications and Audible Warnings

A bi-color LED and buzzer indicate operating status, a ground-fault event, module/wiring faults and

low battery voltage. Refer to the included GFPD-600V product manual for further explanation of

indications and troubleshooting error sequences.

GFPD-600V

Condition

LED / Buzzer

Indication

Start-up

Three green flashes

Normal

Solid green

Ground-fault

Detected or Ground-

fault Trip

Solid red + buzzer (3

sec. beep / min.)

Ground-fault Error

Red fl buzzer

Wiring Error or Open

Breaker Alarm

Red / green flashing

Low Battery Voltage

Threshold Reached

Buzzer (beep 3x /

min.)

Critical Fault

Red / red / green /

green

Содержание TS-MPPT-60-600V-48-DB-TR














































Результаты поиска

Содержание TS-MPPT-60-600V-48-DB-TR

Отзывы:

Morningstar TS-MPPT-60-600V-48-DB-TR, Инструкция по установке, эксплуатации и обслуживанию, Страница: 27 / 45

Результаты поиска

Содержание TS-MPPT-60-600V-48-DB-TR

Отзывы: