Morningstar TS-MPPT-60-600V-48-DB-TR Скачать руководство пользователя страница 40

Страница: 40 / 45

TriStar MPPT-600V-TR Operator's Manual

Warranty and Policies

10.0 Appen-

dix

10.0 Appen-

dix

WARRANTY CLAIM PROCEDURE

1. Before proceeding, please refer to product manual, including Troubleshooting section.
2. Contacting your authorized Morningstar distributor or dealer from whom you purchased the unit is

the first step in the warranty process. Local dealers can often address warranty issues quickly.
3. If supplier is unable to address the issue, please contact Morningstar by e-mail (support@morning-

starcorp.com) with:

(A) purchase location -- business or company name
(B) full model and serial numbers (SN is 8-digits on unit
bar label)
(C) failure behavior, including LED indications
(D) array configuration, panel Pmax, Voc, Vmp, Isc, and

nominal battery voltage; these specifications are

needed to receive assistance.
(E) multi-meter available (for field troubleshooting)

4. After warranty replacement has been approved and new unit(s) received, please return failed

unit(s) using pre-paid shipping label, and follow any product specific instructions if requested by

Morningstar Warranty Dept.
5. If instructed by Morningstar, after warranty replacement shipment has been received, return of

failed unit(s) is

required before further warranty replacements can be

considered for the original or future cases.

NOTE: Please do not return units without an RMA or case number. Doing so will increase the

time required to resolve your claim.

9.0

Technical Specifications

REFER TO THE INCLUDED GFPD-600V OPERATOR'S MANUAL FOR THAT PRODUCT'S

SPECIFICATIONS

Electrical

TS-MPPT-60-600V-48-DB-

TR-GFPD

Nominal System Voltage

48 volts

Maximum Battery Current

60 amps 60 amps

(63A breaker included)

Maximum Solar Input Voltage

600 volts dc 600 volts dc

Battery Operating Voltage Range

16 - 72 volts dc

Maximum Operating Input Current

15 amps

Nominal Maximum Input Power*

3200 watts

Voltage Accuracy

≤ 0.1 % ± 100 mV

Self consumption (tare loss)

2-3.5 watts 2-3.5 watts

Transient Surge Protection

4500 watts / port 4500 watts / port

*These power levels refer to the maximum wattage the TS-MPPT-60-600V-48 can process.

Higher power

arrays

can be used without damaging the controller.

Battery Charging

Charging algorithm

4 - stage

Charging

stages Bulk,

Absorption,

Float,

Equalize

Temperature compensation coefficient

-5 mV / °C / cell (25 °C ref.)

Temperature compensation range (RTS connected)

-30 °C to +80 °C

Temperature compensated set-points:

Absorption, Float, Equalize, HVD

Charging Set-points (48 volt systems):

Settings

Switches

Battery

Type

Absorp.

Stage

Float

Stage

Equalize

Stage

Absorp.

Time

Equalize

Time

Equalize

Timeout

Equalize

Interval

sw: 4-5-6

Volts

Minutes Minutes Minutes

Days

off-off-off

1 - Sealed*

56.00

54.80

150

off-off-on

2 - Sealed*

56.60

54.80

57.60

150

120

off-on-off

3 - Sealed*

57.20

54.80

58.40

150

120

off-on-on 4 - AGM/Flooded

57.60

54.80

60.40

180

120

180

on-off-off

5 - Flooded

58.40

54.00

61.20

180

120

180

on-off-on

6 - Flooded

58.80

54.00

61.60

180

240

on-on-off

7 - L-16

61.60

53.60

64.00

180

240

on-on-on

8 - Custom

Custom

* “Sealed” battery type includes gel and AGM batteries
See section 4.2 for more information

Содержание TS-MPPT-60-600V-48-DB-TR














































Результаты поиска

Содержание TS-MPPT-60-600V-48-DB-TR

Отзывы:

Morningstar TS-MPPT-60-600V-48-DB-TR, Инструкция по установке, эксплуатации и обслуживанию, Страница: 40 / 45

Результаты поиска

Содержание TS-MPPT-60-600V-48-DB-TR

Отзывы: