Morningstar TS-MPPT-60-600V-48-DB-TR Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 45

Morningstar TS-MPPT-60-600V-48-DB-TR Скачать руководство пользователя страница 21

41

TriStar MPPT-600V-TR Operator’s Manual

40

Installation

Step 11 - Power-Up

WARNING: Risk of Damage

Connecting the solar array to the battery terminal will permanently damage the

TS-MPPT-600V-TR.

WARNING: Risk of Damage

Connecting the solar array or battery connection with reverse polarity will permanently damage

the TS-MPPT-600V-TR.

AVERTISSEMENT: Risque d’endommagement

La connexion du réseau solaire sur la borne de la batterie endommagera le TS-MPPT-600V-TR

de façon permanente.

AVERTISSEMENT: Risque d’endommagement

La connexion du réseau solaire ou la connexion de la batterie avec une polarité inversée

endommagera le TS-MPPT-600V-TR de façon permanente.

• Confirm that the solar and battery polarities are correct.
• Note that a battery must be connected to the TS-MPPT-600V-TR to start and operate the

controller. The controller will not operate only from solar input.

• Close the battery disconnect switch first. Observe that the LEDs indicate a successful

start-up. (LEDs blink Green - Yellow - Red for one cycle)

• Close (up position) the GFPD ganged breakers, and verify that the green status light is

ON before continuing.

• Close the solar disconnect switch. If the solar array is in full sunlight, the

TS-MPPT-600V-TR will begin charging. If an optional TriStar Meter is installed, charging

current will be reported along with charging state.

Power-Down

WARNING: Risk of Damage

ONLY disconnect the battery from the TS-MPPT-600V-TR AFTER the solar input has been disconnected.

Damage to the controller may result if the battery is removed while the TS-MPPT-600V-TR is charging.

AVERTISSEMENT: Risque d’endommagement

Le TS-MPPT-600V-TR SEULEMENT déconnecter la batterie APRÈS l’entrée solaire a été

déconnectée. Le contrôleur pourrait endommager si la batterie est retirée quand le TS-MPPT-600V-TR

est en charge.

• To prevent damage, power-down must be done in the reverse order as power-up.

Operation

4.0

The TS-MPPT-600V-TR modes are controlled by a manual transfer switch. After installation has

been completed, there are few operator tasks to perform. However, the operator should be

familiar with the operation and care of the TS-MPPT-600V-TR as described in this section.

4.1 Using the Transfer Switch

The transfer switch allows the user to switch the PV array between the grid-tie inverter and the

TriStar MPPT charge controller. The two positions are illustrated in Figure 4.1 below. Grid-tie

operation is engaged in the horizontal positions; battery charging is enabled in the vertical pos-

tions. In the event of a power outage, move the transfer switch position from “Grid Sell” to “Bat-

tery Backup”. This will redirect the solar array energy from the Grid-tie Inverter to the charge

controller, allowing the backup battery to receive charging current during the outage. When the

AC grid is restored, move the transfer switch back to “Grid Sell” position to resume sell-back of

your solar array energy.

Figure 4-1. TS-MPPT-600V-TR Switch Positions

«
...
19
20
21
22
23
...
»

Содержание TS-MPPT-60-600V-48-DB-TR














































Отзывы:

Нет отзывов