manualshive.com logo in svg

Morningstar TS-MPPT-60-600V-48-DB-TR, Инструкция по установке, эксплуатации и обслуживанию, Страница: 34 / 45

Поделиться
Скачать
Morningstar TS-MPPT-60-600V-48-DB-TR Скачать руководство пользователя страница 34

67

 

 TriStar MPPT-600V-TR Operator's Manual

66

 Testing and Troubleshooting

                     

WARNING:  RISK OF ELECTRICAL SHOCK. 

     

                     

NO  POWER OR ACCESSORY TERMINALS ARE ELECTRICALLY ISOLATED FROM   

       DC INPUT, AND MAY BE  ENERGIZED WITH HAZARDOUS SOLAR VOLTAGE.  UNDER       

       CERTAIN FAULT CONDITIONS, BATTERY COULD BECOME OVER-CHARGED.  TEST          

       BETWEEN ALL TERMINALS AND GROUND BEFORE TOUCHING. 

 

 

          A

VERTISSEMENT:   RISQUE DE CHOC ÉLETRIQUE

.

   

             

NON ALIMENTATION OU AUX BORNES D’ACCESSOIRES SONT ISOLÉS ÉLEC-

TRIQUEMENT DE L’ENTRÉE DE C.C ET DOIT ÊTRE ALIMENTÉS À UNE TENSION DAN-

GEREUSE SOLAIRE. SOUS CERTAINES CONDITIONS DE DÉFAILLANCE, LA BATTERIE 

POURRAIT DEVENIR TROP CHARGÉE. TEST ENTRE TOUTES LES BORNES ET LA MASSE 

AVANT DE TOUCHER. 

             WARNING:  Shock Hazard

             

A means of disconnecting all power supply poles must be provided. These discon-

nects must be incorporated in the fixed wiring.  Open all power source disconnects before 

removing controller wiring cover, or accessing wiring.

               

AVERTISSEMENT:

  

Risque de décharge électrique

 

             Un moyen de déconnexion de tous les poteaux d'alimentation doit être fourni. 

Ceux-ci se déconnecte doit être intégrée dans le câblage fixe. Ouvrir que toutes les source 

d'énergie se déconnecte avant de retirer le couvercle de la contrôleur, ou accès au câblage.

Battery Charging and Performance Issues

Problem: 

No LED indications, controller does not appear to be powered

Solution: 

With a multi-meter, check the voltage at the battery terminals on the TS-MPPT-600V-TR.  

Battery voltage must be 16* vdc or greater. If the voltage on the battery terminals of the control-

ler is between 16 and 72 vdc, and no LEDs are lit, contact your authorized Morningstar dealer for 

service.  If no voltage is measured, check wiring connections, fuses, and breakers.

* Unit will power on with 10V, but 16V is required for charging to occur. 

Problem: 

The TS-MPPT-600V-TR is not charging the battery.

Solution: 

Check the three (3) battery SOC LEDs. If they are flashing a sequence, see 

Section 4.4 Faults & 

Alarms

 of this manual to determine the cause. If a TriStar Meter 2-600V is connected, the 

diagnostics menu will display reported faults and alarms.

 

Testing and Troubleshooting

6.0

If the LED indications are normal, check the fuses, breakers, and wiring connections in the solar 

array wiring. With a multi-meter, check the array voltage directly at the TS-MPPT-600V-TR solar 

input terminals. Input voltage must be greater than battery voltage before charging will begin.

Problem:

Controller makes buzzing and humming noises.

Solution:

No action is required.  This is expected due to magnetic resonance and circuit switching.

Network and Communication Issues

Problem: 

Cannot connect to the controller via RS-232

Solution: 

Check the following:

•  The RS-232 cable is straight-through, not a Null Modem (cross-over)
•  If using a serial-USB adapter, verify that the adapter software is installed and a serial COM 

port has been mapped. Check the activity light on the USB adapter if it has one. If there is 

no activity, the wrong COM port has been chosen or there is a configuration issue with the 

adapter.

•  The default MODBUS ID of the TS-MPPT-600V-TR is 1. Verify that the PC software is 

configured to communicate using the correct ID.

Problem: 

Cannot connect to the controller via EIA-485

Solution: 

Check the following:

•  The RS-232 port is not in use. The EIA-485 and RS-232 ports cannot be used                 

simultaneously. Only one port can be used at a time.

•  The RSC-1 adapter used to connect the PC to the EIA-485 network shows a green LED 

and pulses red when a connection is attempted. See the RSC-1 documentation for more 

information.

•  Each controller or device on the EIA-485 network has been programmed with a unique 

MODBUS ID.

•  A serial cross-over (null modem) cable is used for the connection between the PC and the 

Morningstar RSC-1 485 Adapter. A straight-through serial cable will not work.

•  Power is supplied to the 4-wire bus on the Power/Ground lines. The bus requires voltage 

in the range: 8 - 16 Vdc.

•  All bus connections are secure and each terminal is wired in parallel: line A to line A, line B 

to line B, etc.

Содержание TS-MPPT-60-600V-48-DB-TR














































Отзывы:

Нет отзывов