Morgana AutoCreaser Pro 50 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 40

background image

Page 14

CREASING

4.8

Place the unit on a solid and clear bench ensuring no wires are trapped beneath

the metal side plates.

4.9

Assemble loosely the green drive belt to the pulley

4.10 Replace the unit ensuring the wiring harness is threaded as it was removed

4.11 Attach the belt to the drive shaft.

4.12 Fit the tilt lever to the inside front frame with the bottom button head and screw

in tilt knob.

4.13 Slide rear spacer bar down in position (see below). Fix the bottom screw in and

align the top screw and fit loosely. Replace cable ties to mountings. Align the

roller set square with the fixed lay edge while the front tilt lever is in the centre
position. (Use the rear slots to adjust square) Tighten the screws and replace

the top covers.

«
...
12
13
14
15
16
...
»

Содержание AutoCreaser Pro 50









































Отзывы:

Нет отзывов

Похожие инструкции для AutoCreaser Pro 50

Бренд: Panasonic Страницы: 44

Бренд: Panasonic Страницы: 6

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 6

Бренд: Fellowes Страницы: 4

Бренд: Vendo Страницы: 48

Бренд: JUKI Страницы: 247

Бренд: Janome Страницы: 22

Бренд: Singer Страницы: 68

Бренд: Singer Страницы: 13

Бренд: Consew Страницы: 34

Бренд: DIAKAT Страницы: 10

Бренд: Janome Страницы: 49

Бренд: JUKI Страницы: 4

Бренд: JUKI Страницы: 7

Бренд: JUKI Страницы: 18

Бренд: JUKI Страницы: 40

Бренд: Muratec Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды