background image

Page ii

 

 
 

Safeguards and Precautions 

 

1.  Read and follow all instructions in this manual carefully, and retain this manual for future 

reference. 

 
2.  Do not use this instrument in any manner inconsistent with these operating instructions or 

under any conditions that exceed the environmental specifications stated. 

 

3.  Be sure the power supplied to this instrument matches the specification indicated on the rear 

panel of the instrument 
 

4.  Be sure all power is removed before making or removing any connections to or from this 

instrument. 

 

5.  There are no user serviceable parts in this instrument. Refer service to a qualified technician. 

 

6.  Do not allow cables extending from unit to come into contact with rotating machinery, as 

serious damage to the equipment, or severe personal injury or death may occur as a result 
 

7.  This instrument may not be safe for use in certain hazardous environments, and serious 

personal injury or death could occur as a result of improper use.  Please r

efer to your facility’s 

safety program for proper precautions. 

 

 

In  order  to  comply  with  EU  Directive  2012/19/EU  on  Waste  Electrical  and  Electronic 
Equipment (WEEE):  

This product may contain material which could be hazardous to human 

health and the environment.  DO NOT DISPOSE of this product as unsorted municipal waste.  
This product needs to be RECYCLED in accordance with local regulations, contact your local 
authorities  for  more  information.    This  product  may  be  returnable  to  your  distributor  for 
recycling - contact the distributor for details. 

 

 

 

Monarch Instrument’s Limited Warranty applies. 

See www.monarchinstrument.com for details. 

 

Warranty Registration and Extended Warranty coverage available online at 

www.monarchinstrument.com. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Rev 1.2, June 2019 

Содержание ACT-3X

























Отзывы: