Monacor WAP-202RS, Инструкция по эксплуатации

Страница: 22 / 32

22
Italiano
Method 2: If the router supports
WPS via PIN entry, this method
can be used as an alternative to
the PBC method. Select and con -
firm
PIN
: The menu
WPS Setup
will ap -
pear, showing an 8-digit PIN. Enter
this PIN at the router and press the
knob CONTROL SELECT at WAP-
202RS. Then start the connection at
the router. For detailed information
on how to proceed, also observe the
instructions in the manual / user in -
terface of the router.
If WPS is not to be used, select and
confirm
Skip WPS
. Then enter and
confirm the network key as de -
scribed above.
8) While the network connection is being
established, various messages will
be shown:
Please wait …
Once the network connection has
been established, the message
Con -
nected
will appear, followed by the
message
Setup wizard
Setup wizard
completed
Press SELECT to exit
Press the knob CONTROL SE -
LECT to exit the setup wizard: the
main menu will appear. Use the
main menu or the button MODE
to select the operating mode
desired (chapter 4).
If the wizard fails to establish a con -
nection to the router (message
Failed to
connect
), first check the settings of your
router (e. g. SSID, WPS method used
or network key). You may be able to
improve wireless LAN reception by re -
ducing the distance between the unit
and the router or by realigning the
wireless LAN antenna.
If the network connection is wrong, reset
the network settings (in the menu
“System settings”

Network

Clear net -
work settings
) and then establish the con -
nection again.
3.4 Further settings via the
menu “System settings”
The settings that can be made
via the setup wizard are also
available via the corresponding
menu items of the menu “System
settings”. This menu also provides ad -
ditional setting and display options. An
overview of the options provided by
the menu “System settings” can be
found in fig. 27.
The menu can be called up from any oper-
ating mode: Press the button MENU, turn
the knob CONTROL SELECT to select
System settings
and then press the knob
to confirm. The menu “System set -
tings” will be shown:
System settings
Equaliser
Network
Time/Date
Language
Factory reset
>
>
>
>
For operation of the menu, the follow -
ing generally applies: To select a menu
item or setting, turn the knob; to call up
a menu item or to confirm a setting,
press the knob. To return to the previ -
ous menu level, press the button BACK
or, when in a menu as shown in fig. 17,
select the field “CANCEL” and confirm.
3.4.1 Selecting the menu language
Language
* English
Danish
Dutch
Finnish
French
Select the desired language in this
menu. The following languages are
available: English, Danish, Dutch,
Finnish, French, German, Italian, Nor -
wegian, Polish, Portuguese, Spanish,
Swedish, Turkish.
Once the selection has been con -
firmed, the menu “System settings” will
appear in the language selected.
3.4.2 Display backlight
Backlight
Timeout
On level
Dim level
>
>
>
1) Use
On level
to set the brightness
of the display backlight when the
unit has been switched on. Three
settings are available:
High
,
Medium
and
Low
.
2) Use
Dim level
to set the brightness of
the display backlight when the unit
is in the standby mode. Three set -
tings are available:
Medium
,
Low
and
Off
(no display backlight).
3) Use
Timeout
to set the time the unit
must be in standby mode until the
display backlight changes to the
brightness setting of the standby
mode. Select the desired time or
the setting
On
(the display will not
change to the brightness setting of
the standby mode).