Model Airways Fokker Eindecker E-IV Скачать руководство пользователя страница 52

Страница: 52 / 56

Propeller:

The

Propeller

will be a typical design used for the Eindecker comprising of nine (9) laminations of laser

cut woods alternating with

Basswood

(light);

Cherry

(medium); and

Walnut

(dark)

Locate clean and paint Steel, if not done already the two (2)

Propeller Hub Plates

with bolt heads

(rear) and nuts (front) cast in place. Set aside for now for the paint to dry. See picture below.

Gather the nine (9) laser cut wood

Propeller

Blanks

and sand smooth the edges where the connecting

tabs are located. Once sanded glue them together in the sequence suggested below and on the plans.

Yellow Glue

would be the best to use for the ongoing carving that will happen. Use a 1/8” drill bit to

center and align the

Blanks

as they are being glued together making sure the edges line up and match

each other. Clamp together and let the glue to completely set before carving. Overnight if possible.

Mark with a pencil a reference line

3/32” from the edge down the straight side of the

Propeller Blades

from the center to the tip of the blade. See the picture on the next page. With a sharp hobby blade and
short slicing strokes

carefully carve away 1/32” from the curved trailing edge up to the pencil line.

Develop slowly the curved surface of the blade using the different colors of the wood to keep the
carving even and tapered when getting to the center hub. Some may wish to use the

Propeller Hubs

Plates

to draw lines around the hole as reference lines to carve to as well.

Carving Tips:

Now and

then run the blade through a candle, the wax will lubricate the blade for easier carving. The upper half

Содержание Fokker Eindecker E-IV

























































Результаты поиска

Содержание Fokker Eindecker E-IV

Отзывы:

Бренды по названию

Популярные бренды

Model Airways Fokker Eindecker E-IV, Инструкция по эксплуатации

Результаты поиска

Содержание Fokker Eindecker E-IV

Отзывы:

Бренды по названию

Популярные бренды