Model Airways Fokker Eindecker E-IV Скачать руководство пользователя страница 49

Страница: 49 / 56

Dry fit the

Cylinders

and clean the

Cylinder

seats of any burrs and check the bottom of the

Cylinders

and if necessary file to flat to fit. The

Cylinders

must fit flat and straight up with the spark plugs pointing

to the rear. See pictures above. Once fitted, glue

Cylinders

in place and allow the glue to set.

Drill 1/32” holes in all the posts on both the

Cam Cover

and the

Igniter

. The

Cam Cover

posts will

receive the

1/32”

Pushrods

and th

e Igniter .020”

Copper Wire

. See the picture above.

Paint the

Cam Cover

posts Brass and the

Igniter

posts Copper and do not paint shut the holes and

allow to dry.

Once the paint is dry on the

Cam Cover posts

glue it in place in the recess on the

Front Cover

. Insert

a 1/8” drill bit to align the

Cam Cover

with the

5/32” Brass Sleeve

in the

Crankcase

. Align the

rearward posts with the centerline of forward

Cylinders;

this is necessary for the correct positioning of

the

Pushrods

. See the pictures on the next page.

Содержание Fokker Eindecker E-IV

























































Результаты поиска

Содержание Fokker Eindecker E-IV

Отзывы:

Бренды по названию

Популярные бренды

Model Airways Fokker Eindecker E-IV, Инструкция по эксплуатации

Результаты поиска

Содержание Fokker Eindecker E-IV

Отзывы:

Бренды по названию

Популярные бренды