Model Airways Fokker Eindecker E-IV Скачать руководство пользователя страница 27

Страница: 27 / 56

Once eight (8)

Straps

are cut, sanded smooth with medium sandpaper and ends cut square attach one

end to the center strip of the adjusting photoetched

Slide

part and one

Fastener

end using medium CA

to glue the folded

Strap

to hold the parts. See the picture above. Repeat the process to make four (4)

Seat Belt Straps

. Now position one of the upper

Seat Belts

in place indexed between the

Wind Baffle

and rounded

Cross Member

at the junction of the

Stringer

and cut away the excess for the proper

length with the

Fastener

setting in the middle of the

Seat

. Now match the second

Upper Seat Belt

and cut to length. Glue both

Upper Seat Belts

in place using medium CA with the

Belt

glue joint

pointing down toward the

Seat

. When the CA has set, wet the underside of the

Belt

with water on a Q-

tip and form the wet

Belt

to conform around the

Seat

back. Repeat the process for the

Lower Seat

Belts

indexing between the

Floorboard

and the

Stringer

up against the

Loop

. See the pictures below

as well as the drawing detail on the plan sheet.

Machine Gun Mounting Frame:

Adjust and test fit the

Machine Gun Mounting Frame

to the

Fuselage

angled location sockets on the

Stringers.

The rear curved member fits into the sockets on the

Stringers

and follows the same angle

as the sockets while the front

Frame

member is perpendicular to the

Stringers.

Drill

the sockets open if

necessary for a good fit when the ends are inserted into them. Test fit, and file the inside of the

Frame

members as necessary to fit the assembled

Spent Ammo Can.

See the picture on the next page.

These two parts

MUST

be added together at the same time for a proper build. Once the assembled

Can

is fitted, glue the

Mounting Frame

and

Can

in place on the

Fuselage

. Note that the hinge on the

Can

faces to the rear into the cockpit.

Содержание Fokker Eindecker E-IV

























































Результаты поиска

Содержание Fokker Eindecker E-IV

Отзывы:

Бренды по названию

Популярные бренды

Model Airways Fokker Eindecker E-IV, Инструкция по эксплуатации

Результаты поиска

Содержание Fokker Eindecker E-IV

Отзывы:

Бренды по названию

Популярные бренды