Model Airways Fokker Eindecker E-IV Скачать руководство пользователя страница 50

Страница: 50 / 56

Now drill clean the

Rocker Arms

indexing holes for the

Pushrods

using a 1/32” drill bit. On the

Cylinder Tops

very carefully align vertically the Valve Spring. Paint the

Cylinder Tops

Hull Spar Black

except for the Valve Spring and under surface that will be glued. Glue the

Rocker Arms

to the

Cylinder Tops

indexing the Valve Spring between the tangs on the

Rocker Arms

. See the pictures

below.

Using

1/32” Brass Rod

form

Pushrods

; bend one end of the

Brass Rod

and index it into a

Cam

Cover

post and dry fit a

Rocker Arm

assembly (with cylinder top) on top of a

Cylinder

and cut the

Brass Rod

to length necessary with a slight bend to fit when cut into the hole in the

Rocker Arm

Some trimming may be necessary for flat fit on top of the

Cylinder

to trap the

Pushrod

. Cut seven (7)

pushrods 1 -

1/8” and seven (7) 1” to start with to bend and cut to length as needed.

Содержание Fokker Eindecker E-IV

























































Результаты поиска

Содержание Fokker Eindecker E-IV

Отзывы:

Бренды по названию

Популярные бренды

Model Airways Fokker Eindecker E-IV, Инструкция по эксплуатации

Результаты поиска

Содержание Fokker Eindecker E-IV

Отзывы:

Бренды по названию

Популярные бренды