Model Airways Fokker Eindecker E-IV Скачать руководство пользователя страница 19

Страница: 19 / 56

same with the two (2) Black lines from the

Rudder Bar

. These lines can be sorted out later when being

attached to the

Rudder

and

Elevator.

Tail Skid:

Add the

Tail Skid

inserting and aligning the holes in the

Tail Skid Frame

and secure in place with a

1/4” 00-90

Bolt

and

Nut.

Snug fit the

Nut

so that the

Tail Skid

can move

See the picture on the next

page as well as the plan sheet.

Center

a 12” length of

Bungee Cord

on the loop on the

Tail Skid

and then feed the ends through the

Frame

loops for three times and then seize at the

Tail Skid

loop with a square knot. Treat the knot

lines with CA to cut of the excess to prevent fraying and cut off the excess cord with a sharp blade or
scissors close to the knot.

See the picture above. Using Black thread seize the two (2) Bungee Cord

bundles in three (3) places, center and top and bottom for added detail. See the picture below

Elevator:

Gather the left and right cast metal

Elevator

halves; the cast metal

Control Horns

(2)

; 1/8” x 3/4”

Brass Tube

. Adjust and straighten the two

Elevator

halves to match the plans if not already done.

Mark the two spars 3/8” from each end. See picture on the next page. Apply medium CA to one spar
end surfaces and slip into the

Connector Tube

up to the 3/8” mark; repeat gluing for the other side

while on a flat surface for a matching flat

Elevator

. Once the glue has set, glue the two control horns in

Содержание Fokker Eindecker E-IV

























































Результаты поиска

Содержание Fokker Eindecker E-IV

Отзывы:

Бренды по названию

Популярные бренды

Model Airways Fokker Eindecker E-IV, Инструкция по эксплуатации

Результаты поиска

Содержание Fokker Eindecker E-IV

Отзывы:

Бренды по названию

Популярные бренды