Model Airways Fokker Eindecker E-IV Скачать руководство пользователя страница 15

Страница: 15 / 56

Rudder Support Bar

into the location hole in the

Fuselage Brace

with care that the

Rudder Bar

will

turn freely on the shaft once the glue has set. Next gather the two (2) Black

Rudder Bar

lines straight

back into the cockpit area for now. Tie off the gray lines to the

Fuselage Frame Loops

for the rear

lines and the forward lines to the forward

Fuselage

joints. See picture below.

Glue the

Magneto

and

Oil Pump

to the rear side of the

Cowl Frame Camshaft Support

location holes

with the

Magneto

on the right side and the

Oil Pump

on the left side as seen in the picture below.

Make sure they are arranged on a vertical orientation as seen in the picture below on the right.

Tie four (4) gray lines on the four (4) corners of the

Leather Pad

then tether the

Pad

positioned just

below the air filter attaching to the loops on the

Fuselage Frame

as seen in the picture on the next

page with the view looking up through the bottom of the

Fuselage

Locate the seat assembly parts: the photo etched

Seat Back

, cast metal

Seat Cushion

Seat Frame

Seat Base

and four (4)

Pins

. First, brush the aluminum

Seat Back

horizontally on both sides to

simulate brushed aluminum taking care not to bend or distort the tabs. Next adjust and form the

Seat

Back Frame

and glue to the

Seat Cushion

indexing the locating pins on the

Frame

into the locating

holes on the

Cushion

. Now glue the four (4)

Pins

in place by inserting the

Pins

into the holes in the

Seat Cushion

and add the glue to the

Pins

on the bottom side of the

Seat Cushion

. Once the glue

sets completely cut off the excess

Pin

shafts and add a drop of glue onto the cut off

Pins

. See pictures

on the next page. Glue the

Seat Base

to the

Seat Cushion

indexing the locating pins on the

Base

Содержание Fokker Eindecker E-IV

























































Результаты поиска

Содержание Fokker Eindecker E-IV

Отзывы:

Бренды по названию

Популярные бренды

Model Airways Fokker Eindecker E-IV, Инструкция по эксплуатации

Результаты поиска

Содержание Fokker Eindecker E-IV

Отзывы:

Бренды по названию

Популярные бренды