Mizuho MOT-3602X Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 43

background image

Page 13

SPECIAL USER ATTENTION

NOTE

The table top must be centered or slid
toward the foot end for the Beach Chair
function to operate.

CAUTION

Please use the emergency switch at the
urgent case only.

CAUTION

The safety interlock system is not op-
erational when the emergency back-up
control switches are used.

CAUTION

The EMERGENCY BRAKE LOCK
switch does not activate the brake sys-
tem timer. The switch must be held until
the brakes are completely locked, ap-
proximately 10 seconds.

NOTE

The emergency back-up control
switches will function when the table is
operating on 100 - 240 VAC power,
battery power, or turned off.

NOTE

x

The Emergency Brake Release Valve
must be closed and tightened (coun-
ter-clockwise) before activating any
function.

x

If the Emergency Brake Release Valve
has been operated, the BRAKE
UNLOCK button on the pendant control
will have to be pressed before brakes
will lock again.

NOTE

To make the Back Section easier to
handle, remove the Head Section, pad
and X-ray top prior to removing the
Back Section. Remove the pad and
X-ray top prior to removing the Leg
Section.

WARNING

Ensure that the Leg and Back sections
are properly engaged and secured to
pins before use to prevent injury.

NOTE

The Leg and Back sections are labeled
for proper orientation. The Leg section
cannot be installed on the Back section
pins.

WARNING

Consult manufacturer's instructions
when using high frequency surgical
equipment, cardiac defibrillator and
cardiac defibrillator monitors. Improper
operation procedures might cause a
burn on an operators or patient, and
also cause the malfunction of the
product.

WARNING

x

When a patient is put on a mattress and
his/her position is set up, a patient shall
be set up to more than 1 cm apart from
a side rail so that a patient dose not
touch on side rails (metal).

x

The mattress should be attached in
order not to come off while being in use.

WARNING

When an antistatic pathway is required,
the table has to be used on an antistatic
floor.

WARNING

The antistatic properties of the table are
dependent on the use of the OEM pad
set which was offered with the table or
an alternate approved replacement.

«
...
12
13
14
15
16
...
»

Содержание MOT-3602X












































Отзывы:

Нет отзывов

Похожие инструкции для MOT-3602X

Бренд: Raymarine Страницы: 464

Бренд: 3M Страницы: 8

Бренд: ZOLL Страницы: 3

Бренд: Olsen Страницы: 56

Бренд: Waterous Страницы: 5

Бренд: 3TECH Страницы: 32

Бренд: 4EVAC Страницы: 15

Chicken Coop Plan 3x5

Бренд: EASY COOPS Страницы: 21

Chicken Coop Plan 4x6

Бренд: EASY COOPS Страницы: 18

Chicken Coop Plan 8x10

Бренд: EASY COOPS Страницы: 18

MiniLift160 Classic

Бренд: Handicare Страницы: 28

Бренд: Hands Free Farm Страницы: 24

Бренд: i-Optik Страницы: 75

Бренд: PARAMOUNT BED Страницы: 120

Бренд: Taurus Страницы: 38

Бренд: Phonocar Страницы: 12

Бренд: Spokey Страницы: 4

Бренд: Sweet Sound Electronics Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды