Wiring and Handling of Switches 3
3-1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
3.
Wiring and Handling of Switches
This chapter explains wiring and handling of the operation switches and the grip switch as well
as control of the LEDs for confirming the switch pressing status.
Cautions on installation
•
Use the Handy GOT in the general specifications environment described in this manual.
Do not use the Handy GOT in a place with dusts, soot, conductive dusts, corrosive gas or
flammable gas, place exposed to high temperature, dew condensation, direct sunlight,
wind and rain, or place exposed to vibration or impact.
If the Handy GOT is used in such a place, electrical shock, fire, malfunction, product
damage or deterioration may caused.
•
Never drop cutting chips and electric wire chips into the ventilation window of the Handy
GOT when you drill screw holes or perform wiring.
Otherwise, fire, failure or malfunction may be caused.
•
Connect connection cables securely to the specified connectors while the power is
turned OFF.
Imperfect connection may cause malfunction or failure.
•
When connecting cables, pay attention to the contents described in Chapter 2.
Especially, attach the rear cover so that PCBs inside the Handy GOT are not interfered
with connection cables.
Cautions on wiring
•
Make sure to attach the rear cover to the Handy GOT before turning on the power and
starting operation after the installation or wiring work.
Otherwise, electrical shock may be caused.
•
Make sure to shut down all phases of the power outside the Handy GOT before starting
the installation or wiring work.
Otherwise, electrical shock and damage of Handy GOT may be caused.
Cautions on wiring
•
The Handy GOT has the DC power specifications. Connect the DC power cable to the
dedicated terminals described in this manual.
If the AC power is supplied to the power supply, operation switches or emergency stop
switches, the Handy GOT may be burnt.
•
Correctly connect the 24V DC power cable (terminals) of the Handy GOT to [+][-] of the
DC power supply unit as described in this manual.
If reversing the terminals will seriously damage the Handy GOT.
•
Perform the groundings to the drain wire (FG) of the Handy GOT. Never perform common
grounding with the strong power system.
•
When processing a cable or executing the wiring work, pay attention so that cutting chips
and wire chips do not enter the inside of the Handy GOT.
Such chips may cause fire, failure or malfunction.
A953 HANDY GOT
Содержание A953GOT-LBD-M3-H
