Mitsubishi Heavy Industries FDC1000KXZWE1 Скачать руководство пользователя страница 91

Страница: 91 / 183

–

'14 • KX-SM-200

Error code

Remote control:
7-segment display:

LED

Green

Red

Indoor unit

Heat source unit

Content

E21

–

Defective panel switch

operation (FDT)

Keeps flashing 1-time flash
Keeps flashing

Stays OFF

1. Applicable model

5. Troubleshooting

FDT series only

Diagnosis

Countermeasure

Reset the error and close

the grill.

Insufficient push on the

panel switch at the internal

face of grill

➞

Attach 3 mm thick

rubber sheet at the section

where the panel switch

touches the inside of grill.

Close then the grill.

Disconnected, poorly

connected connectors

➞

Reinsert properly.

・

Defective panel switch

or incorrect panel switch

wiring

➞

Replace panel

switch.

・

Broken wire between

panel PCB (CNV)

➞

Correct or replace wire.

Defective indoor control

PCB

➞

Replace indoor control

PCB.

2. Error detection method

Panel switch (PS) has detected

Open for more than 1 second.

3. Condition of Error displayed

Same as above

4. Presumable cause

• Defective panel switch

• Disconnection of wiring

• Defective indoor control PCB

Note:

Does

matter improve if panel

switch is turned ON forcibly

after resetting

error?

Is grill opened?

YES

Are connectors at right

inserted properly?

Put the switch in the state of

ON by fixing the silicone

section of panel switch with

adhesive tape while it is held

down.

Indoor control PCB: CNV

Is there

continuity between

#1 – #4 of CNV on indoor control PCB

when panel switch operation

is checked?

YES

Silicone guide

Push to turn ON.

Panel switch

→

To CNY1

Содержание FDC1000KXZWE1
























































































































































































Результаты поиска

Содержание FDC1000KXZWE1

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi Heavy Industries FDC1000KXZWE1, Руководство по обслуживанию

Результаты поиска

Содержание FDC1000KXZWE1

Отзывы:

Бренды по названию

Популярные бренды