manualshive.com logo in svg

Mitsubishi Heavy Industries FDC1000KXZWE1, Руководство по обслуживанию

Поделиться
Скачать
Mitsubishi Heavy Industries FDC1000KXZWE1 Скачать руководство пользователя страница 182

Precautions for safety

Read these "Precautions for safety" carefully before starting disassembly work and do it in the proper way.

When disassembling, be sure to turn off the power. When disassembling the electrical components, check the electrical wiring diagram.

The electrical components are under high voltage by the operation of the booster capacitor. 
Fully discharge the capacitor before commencing a repair work. Failure to observe this warning could result in electric shock.

These contents are an example. Please refer to a similar part of actual unit.

1. To remove the corner lid

(1) Remove the inlet grille.
(2) Pull the corner lid toward the direction

indicated by the arrow and remove it.
(The four corner lids are the same way.)

2. To remove the louber motor (LM)

(1) Remove the corner lid.(See No.1)
(2) Remove the louber motor fixing screw

 and remove it.(

 mark)

3. To remove anti draft motor (AM)

(1) Remove the corner lid.(See No.1)
(2) Remove 2 gear box fixing

 screws and remove it.(

 mark)

1. To remove the corner lid

(1) Remove the inlet grille.
(2) Remove the screw(

 mark), pull the corner

lid toword the direction indicated by the
arrow mark.
(The four corner lids are the same way.)

2. To remove the louber motor (LM)

(1) Remove the corner lid.(See No.1)
(2) Remove 2 louber motor fixing screws

 and remove it.(

 mark)

1. To remove the louber motor (LM)

(1) Remove the cover fixing screw and

remove it.(

 mark)

(2) Remove the cam fixing screw and

remove it.(

 mark)

(3) Remove 2 louver motor fixing screws

and remove it.(

 mark)

2. To remove the limit switch (LS)

(1) Remove the cover fixing screw and

remove it.(

 mark)

(2) Remove 2 limit switch fixing screws

and remove it.(

 mark)

1. To remove the corner lid

(1) Take off the corner panel fixing hooks

by a flathead screwdriver and remove it.

2. To remove the louber motor (LM)

(1) Remove the corner lid.(See No.1)
(2) Remove 2 louber motor fixing screws

 and remove it.(

 mark)

DISASSEMBLY PROCEDURE

PROCEDURE  &  PICTURES

FDT series

FDTC series

FDTS

FDTQ series

Corner lid

Corner lid

FDTW series

 '14 • KX-SM-200

–

1

80

 –

Содержание FDC1000KXZWE1
























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды