Mitsubishi Heavy Industries FDC1000KXZWE1 Скачать руководство пользователя страница 77

Страница: 77 / 183

–

'14 • KX-SM-200

Error code

Remote control:
7-segment display:

LED

Green

Red

Indoor unit

Heat source unit

Content

–

Remote control

communication error

Keeps flashing

Stays OFF

Keeps flashing

Stays OFF

1. Applicable model

5. Troubleshooting

All models

Diagnosis

Countermeasure

Is it possible to

reset normally by the power

source reset?

Does

the drain pump start

automatically at one

minutes after power

ON?

Turn SW7-1 OFF.

→

Disconnect the wire

③

between indoor and heat

source units.

YES

Note (1) SW7-1: OFF

→

Note (2) Does the remote control displays “Internal check ON” even

after 3 minutes?

Reset power source

(2)

(1)

Malfunction by temporary

noise.

Check peripheral

environment.

Indoor control PCB

anomaly



Replace it.

Remote control

anomaly



Replace it.

2. Error detection method

When normal communication

between remote control and

indoor unit is interrupted

for more than 2 minutes.

(Detectable only with the

remote control.)

3. Condition of error displayed

Same as above

4. Presumable cause

• Anomalous communication

circuit between remote control

and indoor unit.

• Noise

Note:

If the indoor unit cannot communicate normally with the remote control for 180 seconds, the indoor unit PCB starts to

reset automatically.

Содержание FDC1000KXZWE1
























































































































































































Результаты поиска

Содержание FDC1000KXZWE1

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi Heavy Industries FDC1000KXZWE1, Руководство по обслуживанию

Результаты поиска

Содержание FDC1000KXZWE1

Отзывы:

Бренды по названию

Популярные бренды