Mitsubishi Electric PAC-SIF051B-E Скачать руководство пользователя страница 26

Страница: 26 / 64

5. Dip Switch setting

5.1 DIP Switch Functions

Located on the FTC printed circuit board are 6 sets of small white switches known

as DIP switches. The DIP switch number is printed on the circuit board next to

the relevant switches. The word ON is printed on the circuit board and on the DIP

switch block itself. To move the switch you will need to use a pin or the corner of

a thin metal ruler or similar.

DIP switch settings are listed below in Table 5.1.1.

Only an authorised installer can change DIP switch setting under one’s own re-

sponsibility according to the installation condition.

Make sure to turn off both indoor unit and outdoor unit power supplies before

changing the switch settings.

For multiple outdoor units control with FTC (sub), see section 9.3.2.

DIP switch

Function

OFF

Default settings:

Indoor unit model

SW1 SW1-1 Boiler

WITHOUT Boiler

WITH Boiler

OFF

SW1-2 Heat pump maximum outlet water temperature 55ºC

60ºC

ON *1

SW1-3 DHW tank

WITHOUT DHW tank

WITH DHW tank

OFF: PAC-IF071B-E

ON : PAC-IF072/073B-E

SW1-4 Immersion heater

WITHOUT Immersion heater

WITH Immersion heater

OFF: PAC-IF071B-E

ON : PAC-IF072/073B-E

SW1-5 Booster heater

WITHOUT Booster heater

WITH Booster heater

OFF

SW1-6 Booster heater function

For heating only

For heating and DHW

OFF

SW1-7 Outdoor unit type

Split type

Packaged type

OFF: PAC-IF071B-E

ON : PAC-IF072/073B-E

SW1-8 Wireless remote controller

WITHOUT Wireless remote controller WITH Wireless remote controller

OFF

SW2 SW2-1 Room thermostat1 input (IN1) logic change Zone1 operation stop at thermostat short Zone1 operation stop at thermostat open OFF

SW2-2 Flow switch1 input (IN2) logic change

Failure detection at short

Failure detection at open

OFF

SW2-3 Booster heater capacity restriction

Inactive

Active

OFF

SW2-4 Cooling mode function

Inactive

Active

OFF

SW2-5 Automatic switch to backup heat source op-

eration (When outdoor unit stops by error) Inactive

Active *2

OFF

SW2-6 Mixing tank

WITHOUT Mixing tank

WITH Mixing tank

OFF

SW2-7 2-zone temperature control

Inactive

Active *6

OFF

SW2-8 Flow sensor

WITHOUT Flow sensor

WITH Flow sensor

OFF

SW3 SW3-1 Room thermostat 2 input (IN6) logic change Zone2 operation stop at thermostat short Zone2 operation stop at thermostat open OFF

SW3-2 Flow switch 2 and 3 input logic change

Failure detection at short

Failure detection at open

OFF

SW3-3

—

OFF

SW3-4 Electric energy meter

WITHOUT Electric energy meter

WITH Electric energy meter

OFF

SW3-5 Heating mode function *3

Inactive

Active

SW3-6 2-zone valve ON/OFF control

Inactive

Active

OFF

SW3-7 Heat exchanger for DHW

Coil in tank

External plate HEX

OFF

SW3-8 Heat meter

WITHOUT Heat meter

WITH Heat meter

OFF

SW4 SW4-1 Multiple outdoor unit control

Inactive

Active

OFF

SW4-2 Position of multiple outdoor unit control *7

Sub

Main

OFF

SW4-3

—

OFF

SW4-4 Indoor unit only operation (during installation work) *4 Inactive

Active

OFF

SW4-5 Emergency mode (Heater only operation)

Normal

Emergency mode (Heater only operation) OFF *5

SW4-6 Emergency mode (Boiler operation)

Normal

Emergency mode (Boiler operation) OFF *5

SW5 SW5-1

—

OFF

SW5-2 Advanced auto adaptation

Inactive

Active

SW5-3

—

OFF

SW5-4

—

OFF

SW5-5

—

OFF

SW5-6

—

OFF

SW5-7

—

OFF

SW5-8

—

OFF

SW6

SW6-1

—

OFF: PAC-IF071/072B-E

ON: PAC-IF073B-E

SW6-2

—

OFF

SW6-3 Pressure sensor

Inactive

Active

OFF

SW6-4 Analog output signal (0-10V)

Inactive

Active

OFF

SW6-5

—

OFF

<Table 5.1.1>

<Fig. 5.1.1>

Note:

*1. When the FTC unit is connected with a outdoor unit of which maximum outlet water temperature is 55ºC, DIP SW1-2 must be changed to OFF.

*2. External output (OUT11) will be available. For safety reasons, this function is not available for certain errors. (In that case, system operation must

be stopped and only the water circulation pump keeps running.)

*3. This switch functions only when the cylinder unit is connected with a PUHZ-FRP outdoor unit. When another type of outdoor unit is connected,

the heating mode function is active regardless of the fact that this switch is ON or OFF.

*4. Space heating and DHW can be operated only in indoor unit, like an electric heater. (Refer to "5.7 Indoor unit only operation". )

*5. If emergency mode is no longer required, return the switch to OFF position.

*6. Active only when SW3-6 is set to OFF.

*7. SW4-2 is available only when SW4-1 is ON.

SW1

SW3

SW4

SW2

SW5

SW6

Содержание PAC-SIF051B-E

































































Результаты поиска

Содержание PAC-SIF051B-E

Отзывы:

Похожие инструкции для PAC-SIF051B-E

Бренды по названию

Популярные бренды

Mitsubishi Electric PAC-SIF051B-E, Руководство по установке

Результаты поиска

Содержание PAC-SIF051B-E

Отзывы:

Похожие инструкции для PAC-SIF051B-E

Бренды по названию

Популярные бренды