Mitsubishi Electric PAC-SIF051B-E Скачать руководство пользователя страница 22

Страница: 22 / 64

SW1

SW3

SW4

SW2

SW5

SW6

4. Electrical work

<Wiring for booster heater with a built-in direct cut-off thermostat>

Earth leakage

circuit breaker for

booster heater

Contactor or

relay for booster

heater

Booster heater1

Booster heater2

Direct cut-off

thermostat

Contactor or

relay for

booster heater 2

Contactor or

relay for

booster heater 2

OUT6

(TBO.5 5-6)

Earth leakage

circuit breaker for

immersion heater

Contactor or relay

for immersion

heater

Immersion heater

Direct cut-off

thermostat

OUT9

(TBO.4 5-6)

Earth leakage

circuit breaker for

booster heater

Contactor or relay

for protecting

booster heater

Indirect cut-off

thermostat

(TBO.5 3-4)

Contactor or

relay for booster

heater 1

OUT6

(TBO.5 5-6)

OUT7

(TBO.5 7-8)

BHT

(TBO.5 1-2)

Booster heater1

Booster heater2

OUT7

(TBO.5 7-8)

<Wiring for booster heater with a built-in indirect cut-off thermostat>

<Wiring for immersion heater with a built-in direct cut-off thermostat>

<Fig. 4.6.1>

<Fig. 4.6.2>

<Fig. 4.6.3>

4.6 Wiring for heater

The initial setting assumes that the connected booster heater(s) has a built-in direct cut-off thermostat. <Fig. 4.6.1>

When the connected booster heater(s) has a built-in indirect cut-off thermostat, perform wiring according to the following items. < Fig. 4.6.2>

• Connect the thermostat signal to BHT (TBO.5 1-2).

• Remove the jumper wire from connector CNBHT.

• Connect a contactor (or relay) for protecting the booster heater.

(Connect the electromagnetic coil terminals to BC (TBO.5 3-4).

Do not remove the jumper wire from connector CNBHT when the connected booster heater(s) has a built-in direct cut-off thermostat. < Fig. 4.6.1>

The initial setting assumes that the connected immersion heater has a built-in direct cut-off thermostat. <Fig. 4.6.3>

Содержание PAC-SIF051B-E

































































Результаты поиска

Содержание PAC-SIF051B-E

Отзывы:

Похожие инструкции для PAC-SIF051B-E

Бренды по названию

Популярные бренды

Mitsubishi Electric PAC-SIF051B-E, Руководство по установке

Результаты поиска

Содержание PAC-SIF051B-E

Отзывы:

Похожие инструкции для PAC-SIF051B-E

Бренды по названию

Популярные бренды