Mitsubishi Electric PAC-SIF051B-E Скачать руководство пользователя страница 60

Страница: 60 / 64

10. Supplementary information

10.1 Refrigerant collecting (pumpdown) for split model systems only

Refer to “Refrigerant collection” in the outdoor unit installation manual or service manual.

10.2 Back-up operation of boiler

Heating operation is backed up by boiler.

For more details, refer to the installation manual of PAC-TH012HT-E.

<Installation & System set up>

1. Set Dip-SW 1-1 to ON "With boiler" and SW2-6 to ON “With Mixing tank”.

2. Install the thermistors THWB1 (Flow temp.) *1 on the boiler circuit.

3. Connect the output wire (OUT10: Boiler operation) to the signal input (room thermostat input) on the boiler. *2

4. Install one of the following room temp. thermostats. *3

Wireless remote controller (option)

Room temp. thermostat (local supply)

Main remote controller (remote position)

*1 The boiler temp. thermistor is an optional part.

*2 OUT10 has no voltage across it.

*3 Boiler heating is controlled on/off by the room temp. thermostat.

<Remote controller settings>

1. Go to Service menu > Heat source setting and choose “Boiler” or “Hybrid”. *4

2. Go to Service menu > Operation settings > Boiler settings to make detailed settings for “Hybrid” above .

*4 The “Hybrid” automatically switches heat sources between Heat pump (and Electric heater) and boiler.

Product fiche of temperature control

(a) Supplier’s name: MITSUBISHI ELECTRIC CORPORATION

(b) Supplier’s model identifier: PAR-WT50R-E and PAR-WR51R-E

(d) The contribution of the temperature control to seasonal space heating energy efficiency: 4%

Содержание PAC-SIF051B-E

































































Результаты поиска

Содержание PAC-SIF051B-E

Отзывы:

Похожие инструкции для PAC-SIF051B-E

Бренды по названию

Популярные бренды

Mitsubishi Electric PAC-SIF051B-E, Руководство по установке

Результаты поиска

Содержание PAC-SIF051B-E

Отзывы:

Похожие инструкции для PAC-SIF051B-E

Бренды по названию

Популярные бренды