Mitsubishi Electric PAC-SIF051B-E, Руководство по установке

Страница: 20 / 64

19
4.5 Connecting inputs/outputs
For multiple outdoor units control with FTC (Sub), see section 9.
CN108
CN01
(BK)
1
3
CN3C
(BU)
CNPWM
(WH)
1
5
CNRF
(WH)
CN105
(RD)
CNIT
(BU)
1
2
CN20
(RD)
TBI.1
LED3
LED4
TAB1
8
1
2
3
4
5
6
1
2
3
4
5
6
7
8
CNP1
(WH)
TBO.1
1
5
3
1
5
SW6
1
3
1
5
1
5
LED2
1
SW1
8
1
SW2
8
1
SW3
1
SW4
6
8
1
SW5
LED1
1
3
1
3
CNP4
(RD)
TBO.2
1
2
3
4
5
6
TBO.3
CNV1
(WH)
1
3
5
1
2
3
4
5
6
7
8
TBO.4
CNIH
(OG)
1
3
CNBHT
(BK)
1
3
CN21
(YE)
1
3
CNW12
(RD)
1
4
CNW5
(BU)
1
4
1
4
CN1A
(WH)
6 8 7 5 2 1
TBI.2
6 8 7 5 2 1
TBI.3
6 8 7 5 4 2 1
TBI.4
6 8 7 5 2 1
TBI.5
6 8 7 5 2 1 6 8 7 5 2 1
TBI.6
1
4
CN401
(WH)
F2 F1
1
2
3
4
5
6
7
8
TBO.5
3 4 3 4 3 4 3 4 3 4 3
en
4. Electrical work
Signal inputs
Item Name Model and specifications
Signal input
function
Signal input
wire
Use sheathed vinyl coated cord or cable.
Max. 30 m
Wire type: CV, CVS or equivalent
Wire size: Stranded wire 0.13 mm² to 0.52 mm²
Solid wire: ø0.4 mm to ø0.8 mm
Switch Non-voltage “a” contact signals
Remote switch: minimum applicable load 12 V DC, 1 mA
Wiring specification and local supply parts
Name Terminal
block
Con-
nector Item
OFF (Open) ON (Short)
IN1 TBI.1 7-8 — Room thermostat 1 input *1 Refer to SW2-1 in <5.1 DIP Switch Functions>.
IN2 TBI.1 5-6 — Flow switch 1 input Refer to SW2-2 in <5.1 DIP Switch Functions>.
IN3 TBI.1 3-4 — Flow switch 2 input (Zone1) Refer to SW3-2 in <5.1 DIP Switch Functions>.
IN4 TBI.1 1-2 — Demand control input Normal Heat source OFF/ Boiler operation *3
IN5 TBI.2 7-8 — Outdoor thermostat input *2 Standard operation Heater operation/ Boiler operation *3
IN6 TBI.2 5-6 — Room thermostat 2 input *1 Refer to SW3-1 in <5.1 DIP Switch Functions>.
IN7 TBI.2 3-4 — Flow switch 3 input (Zone2) Refer to SW3-2 in <5.1 DIP Switch Functions>.
IN8 TBI.3 7-8 — Electric energy meter 1
*4 IN9 TBI.3 5-6 — Electric energy meter 2
IN10 TBI.2 1-2 — Heat meter
IN11 TBI.3 3-4 —
Smart grid ready input *5
IN12 TBI.3 1-2 —
INA1 TBI.4 1-3 CN1A Flow sensor input *6
*1. Set the ON/OFF cycle time of the room thermostat for 10 minutes or more; otherwise the compressor may be
damaged.
*2. If using outdoor thermostat for controlling operation of heaters, the lifetime of the heaters and related parts may
be reduced.
*3. To turn on the boiler operation, use the main remote controller to select “Boiler” in “External input setting“
screen in the service menu.
*4. Connectable electric energy meter and heat meter
● Pulse type Voltage free contact for 12VDC detection by FTC
(TBI.2 1 pin, TBI.3 5 and 7 pins have a positive voltage.)
● Pulse duration Minimum ON time: 40ms
Minimum OFF time: 100ms
● Possible unit of pulse 0.1 pulse/kWh 1 pulse/kWh 10 pulse/kWh
100 pulse/kWh 1000 pulse/kWh
Those values can be set by the main remote controller. (Refer to the menu tree in "7.2 Main remote controller".)
*5. As for the smart grid ready, refer to "4.9 Smart grid ready".
*6. Connectable flow sensor
● Power supply 5 V DC
● Measuring range 5 to 100 L/min
Those values can be set by the main remote controller. (Refer to <Auxiliary setting> on this page.)
● Flow signal 0.5 V (at minimum flow rate) to 3.5 V (at maximum flow rate)
<Fig. 4.5.1>
<Auxiliary settings>
This function is used to set the parameters for any auxiliary parts used in the system
Menu subtitle Function/ Description
Economy settings for pump Water pump stops automatically in certain period of time from when operation is finished.
Delay Time before pump switched off*1
Electric heater (Heating) To select “WITH booster heater (ON)” or “WITHOUT booster heater (OFF)” in Heating mode.
Delay The minimum time required for the booster heater to turn ON from after Heating mode has started.
Electric heater (DHW) To select "WITH (ON)" or "WITHOUT (OFF)" booster heater or immersion heater individually in DHW mode.
Delay The minimum time required for the booster heater or immersion heater to turn ON from after DHW mode has started.
(This setting is applied for both booster and immersion heater.)
Mixing valve control *2 Running Period from valve fully open (at a hot water mixing ratio of 100%) to valve fully closed (at a cold water mixing ratio of 100%)
Interval Interval (min) to control the Mixing valve.
Flow sensor *3 Minimum The minimum flow rate to be detected at Flow sensor.
Maximum The maximum flow rate to be detected at Flow sensor.
*1. Decreasing "time before pump switched off" may increase the duration of stand-by in Heating/Cooling mode.
*2. Set the Running time according to the specifications of the actuator of each mixing valve. It is recommended to set the interval to 2 minutes that is a default value.
With the interval set longer, it could take longer to warm up a room.
*3. Do not change the setting since it is set according to the specification of Flow sensor attached to the indoor unit.
Note:
Stranded wire should be processed with insulation-covered bar terminal
(DIN46228-4 standard compatible type).