Mitsubishi Electric Melsensor CF26-LR Скачать руководство пользователя | Manualshive

Страница: 96 / 112

background image

94

APPX
Appendix 7 Exposure Time, Gain Factor, and Image Filtering



Click the [Add] button and select a filter type to use from "Filter Properties" to set the filter parameters.



Set an image to use for reading codes.

Original: Read an acquired image.
Filtered: Read a filtered image.
(In this example, the set filtered image is used for reading DataMatrix codes.)



By selecting a code to be read for "No Read Image" (DataMatrix in this example), a filtered image is displayed even when

code reading is failed.
<Frequently used filter types>
Dilate: An image with a bright part being dilated.
Erode: An image with a dark part being dilated.
Stretch: To enlarge a difference of brightness and darkness of an image. When increasing the 'Low' value, the gray color in
the image will become closer to black. When decreasing the 'High' value, the gray color will become closer to white.

Ó

Ô

Õ

«
...
94
95
96
97
98
...
»

Содержание Melsensor CF26-LR

















































































































Отзывы:

Нет отзывов

Похожие инструкции для Melsensor CF26-LR

QUICKSCAN 6000 PLUS

Бренд: Datalogic Страницы: 104

Бренд: Yarvik Страницы: 20

Бренд: zeroblue Страницы: 2

Бренд: L-Tron Страницы: 4

Бренд: Netum Страницы: 17

Бренд: Symbol Страницы: 112

XTT909-1-0-GB-XX

Бренд: impro Страницы: 8

NFT 1125 Series

Бренд: Opticon Страницы: 61

Бренд: Creator Страницы: 16

Бренд: Toshiba Страницы: 20

Бренд: Estar Страницы: 8

DRAGON D Series

Бренд: Datalogic Страницы: 21

Бренд: Unitech Страницы: 2

Бренд: Cub Страницы: 4

Бренд: RIOTEC Страницы: 2

Бренд: Leuze electronic Страницы: 154

Бренд: 3M Страницы: 33

Бренд: 3nStar Страницы: 78

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды