Mitsubishi Electric MELFA RV-13FR Series Скачать руководство пользователя страница 187 | Manualshive

Страница: 187 / 200

background image

5 Maintenance and Inspection

Resetting the origin 5-175

5.6.3 ABS origin method

When the origin setting of the robot is performed for the first time, this product records the angular position of the
origin within one rotation of the encoder as the offset value. If the origin setting is performed according to the
ABS origin method, this value is used to suppress variations in the origin setting operations and to reproduce the
initial origin position accurately.

This operation is carried out with the teaching pendant. Set the mode of the controller to "MANUAL", and set the
[ENABLE] switch on the teaching pendant to "ENABLE" to enable the teaching pendant.
First, set to the ABS mark arrow of the axis for which the origin is to be set with jog operation. This can be set for
all axes simultaneously or each axis independently.
To align the ABS marks, view the robot from the front. The deviation between the end points of the two triangular
marks must be 1 mm or less.
The positions where the ABS mark is attached are shown in below. Refer to

Page 24, "2.3 Confirming the

for details on the jog operation.

(1) RV-2FR series

Fig.5-36 ： ABS mark attachment positions (RV-2FR series)

㻶㻡㻌㼍㼤㼕㼟

㻶㻞㻌㼍㼤㼕㼟

㻶㻝㻌㼍㼤㼕㼟

㻶㻢㻌㼍㼤㼕㼟

㻭㻮㻿㻌㼙㼍㼞㼗㻌㻔㻶㻞㻌㼍㼤㼕㼟㻕

㻭㻮㻿㻌㼙㼍㼞㼗㻌㻔㻶㻢㻌㼍㼤㼕㼟㻕

㻶㻠㻌㼍㼤㼕㼟

㻶㻟㻌㼍㼤㼕㼟

㻭㻮㻿㻌㼙㼍㼞㼗

㻭㻮㻿㻌㼙㼍㼞㼗

㼂㼕㼑㼣㻌㻭㻌㻔㻶㻢㻌㼍㼤㼕㼟㻕

㼂㼕㼑㼣㻌㻮㻌㻔㻶㻞㻌㼍㼤㼕㼟㻕

㻭

㻮

㻭㻮㻿㻌㼙㼍㼞㼗

ＡＢＳマーク拡大図

ＡＢＳマークの設定範囲

1mm以内

1mm以内

(プラス側ずれ量)

(マイナス側ずれ量)

ABS mark

Within 1mm

Within 1mm

(+ side deviation)

(- side deviation)

Setting range of ABS mark

Note) The figure is reference to show the sticking position of the ABS mark.

The angles of each axis which sets up the ABS origin are shown below.
J1 axis: 0 degrees, J2 axis: 0 degrees, J3 axis: 90 degrees, J4 axis: -50 degrees, J5 axis: 75 degrees, J6
axis: 0 degrees.

«
...
185
186
187
188
189
...
»

Содержание MELFA RV-13FR Series









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MELFA RV-13FR Series

Бренд: SCHUNK Страницы: 2

Бренд: TDX Tech Страницы: 27

XTCEH600 Series

Бренд: Eaton Страницы: 6

Бренд: Festo Страницы: 42

Бренд: Magnum Industrial Страницы: 9

BNI CCL-502-100-Z001

Бренд: Balluff Страницы: 193

Бренд: Endura Страницы: 10

Бренд: PCB Piezotronics Страницы: 6

SmartCase SC1230

Бренд: SixCase Страницы: 48

PAR Source Phantom DE1000Lh

Бренд: Hydrofarm Страницы: 12

Бренд: Eaton Страницы: 3

AutoBoom XRT Series

Бренд: Raven Страницы: 64

Бренд: Magikist Страницы: 12

Бренд: M&R Страницы: 43

Бренд: ZIPPER MASCHINEN Страницы: 67

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 16

Бренд: VALTIR Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды