Mitsubishi Electric FDF100VNVD Скачать руководство пользователя страница 168

Страница: 168 / 211

167

Heating overload operation

Keeps flashing 1 time flash
Keeps flashing

Stays OFF

1. Applicable model

5. Troubleshooting

All models

Diagnosis

Countermeasure

YES

(2)

Is the air filter clogged?

Is the

indoor heat exchanger

temperature thermistor

connection OK?

Are the

characteristics of indoor

heat exchanger temperature

thermistor OK?

Check the error data with the

remote controller.

YES

Is the unit

operating in the state of

heating overload?

Note (1) Judge if it is in the state of overload or not as follows.

�

Is there any short-circuit of air?

�

Isn’t there any fouling or clogging on the indoor heat exchanger?

�

Is the outdoor fan control normal?

�

Isn't the room and outdoor air temperature too high?

Note (2) For characteristics of indoor heat exchanger temperature thermistor,

see the error display E6.

YES

Error stop

Reset

Indoor heat exchanger temperature (°C)

Wash.

Defective indoor heat

exchanger temperature

thermistor connector

➞

Correct.

Defective indoor heat

exchanger temperature

thermistor.

Check refrigerant system.

Adjust

2. Error detection method

Indoor heat exchanger

temperature thermistor (ThI-R1,

R2, R3)

3. Condition of Error displayed

When it is detected 5 times

within 60 minutes from initial

detection or when the overload

condition is detected for 6

minutes continuously.

4. Presumable cause

• Clogged air filter

• Defective indoor heat

exchanger temperature

thermistor connector

• Defective indoor heat

exchanger temperature

thermistor

• Anomalous refrigerant system

Note:

During heating operation; After starting compressor, compressor rotation speed is decreased by detecting indoor heat

exchanger temperature (Thi-R) in order to control high pressure.

Error code

Remote controller:

LED

Green

Red

Indoor

Outdoor

Content

'11 • PAC-T-160

Содержание FDF100VNVD




















































































































































































































Результаты поиска

Содержание FDF100VNVD

Отзывы:

Похожие инструкции для FDF100VNVD

Бренды по названию

Популярные бренды

Mitsubishi Electric FDF100VNVD, Техническое руководство

Результаты поиска

Содержание FDF100VNVD

Отзывы:

Похожие инструкции для FDF100VNVD

Бренды по названию

Популярные бренды