Mindray Trio Скачать руководство пользователя страница 36

Страница: 36 / 82

Trio™ Service Manual

0070-10-0591-01

2 - 11

Calibration/Maintenance

Calibration and System Checks

2.4.3

Safety Tests

Equipment: Safety Analyzer (Dempsey Model 431 or equivalent).

2.4.3.1

Leakage Current Tests

Case Leakage

Plug the line cord of the unit into the safety analyzer.

Connect the case ground lead of the analyzer to the equipotential lug of the monitor (at
rear of monitor).

Perform the tests under the following conditions:

Case Grounded:
Normal polarity
Polarity with open neutral

Case Ungrounded
Normal polarity
Polarity with open neutral
Reverse polarity

Verify the current reading of the test is <100µA under normal operating conditions;
<300µA under a single fault condition for 120 VAC and <500µA under a single fault
condition for 230 VAC.

Patient Leakage

Perform the test under the following conditions:

Lead to ground: Sink current patient circuit (Test V Model 431 Dempsey)

Patient leakage with line voltage on leads

Connect the ground wire from the safety analyzer to the equipotential lug of the monitor.

Connect the ECG cable from the analyzer to the monitor.

On the safety analyzer, depress the

APPLY 115 VAC

button and note the reading.

Repeat the test for normal and open ground polarity combinations.

Verify the current readings of the test are <50µA under a single fault condition.

Содержание Trio



















































































Результаты поиска

Содержание Trio

Отзывы:

Похожие инструкции для Trio

Бренды по названию

Популярные бренды

Mindray Trio, Руководство по обслуживанию

Результаты поиска

Содержание Trio

Отзывы:

Похожие инструкции для Trio

Бренды по названию

Популярные бренды