![background image](http://html1.mh-extra.com/html/milwaukee/4933471844/4933471844_original-instructions-manual_1797701013.webp)
24
25
ENGLISH
ENGLISH
ENGLISH
ONE-KEY™ Indicator
Solid Blue
Wireless mode is active and ready to be
con
fi
gured via the ONE-KEY™ app.
Blinking Blue
Tool is actively communicating with the
ONE-KEY™ app.
Blinking Red
Tool is in security lockout and can be
unlocked by the owner via the ONE-
KEY™ app.
MAINS CONNECTION
Connect only to single-phase AC current and only to the
system voltage indicated on the rating plate. It is also
possible to connect to sockets without an earthing contact
as the design conforms to safety class II.
CHARGING TIME
Battery Cat. No.
Volts
Capacity
Charging Time
approx.
MXFCP203
72 V
≤
3.0 Ah
45 min
MXFXC406
72 V
≤
6.0 Ah
90 min
LI-ION BATTERIES
The rechargeable batteries are partially charged. The LED
on the battery indicates the state of charge.
If it is not used for long periods, the rechargeable battery
will switch to the non-operative state.
When fully discharged the rechargeable battery switches
o
ff
automatically (depth discharge not possible).
Under extreme circumstances, the internal temperature of
the battery could become to high. If this happens, the
battery will shut down.
Place the battery on the charger to charge and reset it.
The state of charge can be read by pressing the button on
the rechargeable battery. The battery can be left in the
electric tool while the reading is taken but it must be
switched o
ff
at least one minute beforehand (otherwise the
display will be inaccurate). The number of LEDs illuminated
indicates the state of charge. A
fl
ashing LED indicates a
max. power reserve of 10%.
As a general principle, if the electric tool should fail to work
after inserting the rechargeable battery, then the battery
should be plugged into the charger. The displays on the
battery and charger will then provide information about the
condition of the battery.
In low temperatures work may continue at reduced output.
CHARACTERISTICS
After inserting the battery into the reception of the charger
the battery will automatically be charged (red control lamp
is illuminated continuously)
When a hot or cold battery pack is inserted into the charger
(
fl
ashing red lamp), charging will begin automatically once
the battery reaches the correct charging temperature
(0°C...40°C). The max. charging current is
fl
owing when
the temperature of the Li-Ion-battery is between 0°C and
30°C.
The battery’s charging time is between 45 min and 90 min,
depending on the state of discharge.
Once the battery is fully charged, the LED on the charger
changes from red to green.
Remove the battery pack from the tool for charging when
convenient for you and your job. Milwaukee batteries do
not develop a memory when charged after only a partial
discharge. It is not necessary to run down the battery pack
before placing it on the charger.
As a general practice, it is best to unplug battery chargers
and remove batteries when not in use. No battery pack
damage will occur, however, if the charger and battery pack
are left plugged in.
The charger will keep the battery pack fully charged if it is
left on the charger. The light indicator will be same as
normal charging.
If the light indicator
fl
ashes red and green, check that the
battery pack is fully seated into the bay. Remove the
battery pack and reinsert. If the light continues to
fl
ash red
and green, remove pack(s) and unplug charger for at least
2 minutes. After 2 minutes, plug charger back in and insert
pack. If the problem persists, contact a MILWAUKEE
service facility.
LIGHT INDICATORS
Continuous red
Charging
Slow
fl
ashing
green
Approaching full charge
Continuous green
Charging is complete
Fast
fl
ashing red
Battery or charger is too
hot/cold - charging will
begin/resume when battery
or charger reaches correct
charging temperature
Flashing red/
green
Damaged or faulty battery
pack or charger
BATTERIES
Battery packs which have not been used for some time
should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the
performance of the battery pack. Avoid extended exposure
to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept
clean.
For an optimum life-time, the battery packs have to be fully
charged, after used.
To obtain the longest possible battery life remove the
battery pack from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below
27°C and away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
BATTERY PACK PROTECTION
The battery pack has overload protection that protects it
from being overloaded and helps to ensure long life.
Under extreme stress the battery electronics switch o
ff
the
machine automatically. To restart, switch the machine o
ff
and then on again. If the machine does not start up again,
the battery pack may have discharged completely. In this
case it must be recharged in the battery charger.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in
accordance with local, national and international provisions
and regulations.
• The user can transport the batteries by road without
further requirements.
• Commercial transport of Lithium-Ion batteries by third
parties is subject to Dangerous Goods regulations.
Transport preparation and transport are exclusively to be
carried out by appropriately trained persons and the
process has to be accompanied by corresponding
experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and
insulated to prevent short circuit.
• Ensure that battery pack is secured against movement
within packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
MAINTENANCE
The light source contained in this luminaire shall only be
replaced by the manufacturer or his service agent or a
similar quali
fi
ed person.
Use only Milwaukee accessories and spare parts. Should
components need to be replaced which have not been
described, please contact one of our Milwaukee service
agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the machine type printed as well as the
six-digit No. on the label and order the drawing at your
local service agents or directly at: Techtronic Industries
GmbH, Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any
work on the machine.
Always disconnect the plug from the socket
before carrying out any work on the machine.
CAUTION: Possibly hazardous optical radiation
emitted from this product. Do not stare at
operating lamp. May be harmful to the eye.
Please read the instructions carefully before
starting the machine.
Do not swallow the coin cell battery!
Do not dispose electric tools, batteries/
rechargeable batteries together with household
waste material.
Electric tools and batteries that have reached
the end of their life must be collected separately
and returned to an environmentally compatible
recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
Class II tool.
Tool in which protection against electric shock
does not rely on basic insulation only, but in
which additional safety precautions, such as
double insulation or reinforced insulation, are
provided.
There being no provision for protective earthing
or reliance upon installation conditions.
Do not burn used battery packs.
Never charge a damaged battery pack. Replace
by a new one.
European Conformity Mark
British Confomity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark
Содержание 4933471844
Страница 3: ...4 5 8 6 20 10 21 12 19 18 16 14 ON OFF ...
Страница 7: ...12 13 1 4 5 2 3 ...
Страница 11: ...20 21 1 2 3 3V CR2032 ...
Страница 66: ...130 131 ...