![background image](http://html1.mh-extra.com/html/milwaukee/4000474838/4000474838_original-instructions-manual_1797742016.webp)
30
31
ENGLISH
ENGLISH
• Ensure that battery pack is secured against movement
within packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
ADDITIONAL HINTS FOR OPERATION
Using forward/OFF/reverse switch (see picture section)
1. For forward (clockwise) rotation, move the forward/OFF/
reverse switch to the arrow pointing
2. For reverse (counterclockwise) rotation, turn the
forward/OFF/reverse switch to the arrow pointing away
from the nose of the drum . Check the direction of
rotation before use. NOTE: Only use Reverse to clear
jammed cable. Do not use Reverse to retract the cable.
3. To turn the rotation OFF and lock the switch, turn the
forward/OFF/reverse switch to the center position O.
The foot pedal will not work while the forward/OFF/
reverse switch is in the center locked position. Always
lock the switch or remove the battery pack before
performing maintenance, changing accessories, storing
the machine and any time the machine is not in use.
Starting and stopping speed
1. To start the machine, push the forward/OFF/reverse
switch to forward and step or kneel on the foot pedal.
2. To stop the machine, release pressure on the pedal.
Then, push the forward/OFF/reverse switch to the
center position O.
Inserting cable into drain
1. Transport and set the machine up according to these
instructions.
2. Ensure the cable feed is disengaged.
3. Grasp the cable close to the machine and feed at least
2' of cable into the drain by hand.
WARNING!
Wear leather gloves.
4. Move the forward/OFF/reverse switch to forward and
press the foot pedal to begin rotating the cable.
5. Feed the cable into the drain. Use the cable feed in
"advance" if desired. Continue until the obstruction is
reached.
NOTE:
If more cable is needed to reach the clog,
disconnect the original cable from the anchor cable.
Then, either load additional cable into the machine and
connect the two cables together, or connect the original
cable to the cable in another machine.
WARNING!
Never feed more than 100' of cable into the
machine to avoid overloading.
6. When the clog is reached, disengage the auto feed.
Manually move the cable in a back and forth motion
until the obstruction is cleared. If the machine binds,
release pressure from the foot pedal immediately.
Repeat until the drain is clear.
To unbind cable in the drain
To relieve torque (twisting) on the cable:
1. Disengage the cable feed.
2. Move the forward/OFF/reverse switch to reverse and
pulse the foot pedal once to begin rotating the cable. Do
not hold down the foot pedal.
3. Pull the cable back out from the drain a few inches to
free the cable.
4. After the cable is freed from the obstruction and the
machine has come to a complete stop, switch back to
forward and continue working the obstruction.
Caution!
Running the machine in reverse for extended
periods can cause damage to the cable and
accessories.
Removing cable from drain
1. Move the forward/OFF/reverse switch to forward and
press the foot pedal to begin rotating the cable.
2. Pull the cable away from the drain and feed it into the
drum. Use the cable feed in "retract" if desired.
3. As the working end of the cable is neared, feed the last
5' of cable into the machine by hand. Do not use cable
feed.
WARNING!
Never feed more than 100' of cable into the
machine to avoid overloading.
4. Remove the drain plug and drain into a suitable
location.
5. Before storing the machine, wash the cable and drum
(see "Cleaning Cables and Drum" in Maintenance).
Hoisting
If it becomes necessary to hoist the machine, use the center
of the transport handle as the anchor point. Ensure the
hoisting strap will not slip or con- tact other parts, such as
the POWERTREDZTM lift assist trigger.
CABLE INSTALLATION
Selecting the proper cable:
5/8" x 25' Inner Core Drum Cable
5/8" x 50' Inner Core Drum Cable
5/8" x 100' Inner Core Drum Cable
3/4" x 25' Inner Core Drum Cable
3/4" x 50' Inner Core Drum Cable
3/4" x 100' Inner Core Drum Cable
3/4" Anchor Cable
3/4" x 2' Leader Cable
5/8" x 2' Leader Cable
Cable Attachments for 5/8“ and 3/4“ Cables
Straight Auger
Funnel Auger
3" Root Cutter
4" Root Cutter
6" Root Cutter
Small Opening Tool
Medium Opening Tool
3" Grease Cutter
4" Grease Cutter
Head Attachement Kit
To prevent damage to the cable and attachments, only use
in recommended size
For cable installation see picture section.
WARNING!
Cable is under pressure and can recoil
unexpectedly during installation, which may result in
personal injury.
To reduce the risk of injury, wear safety goggles or glasses
with side shields. Always wear leather gloves.
Grasp cable
fi
rmly. Pull out the slide action cable lock,
revealing the inner drum with cable. Firmly grasp the cable
before setting the slide action cable lock aside.
Wind the new cable into the inner drum in the arrow
direction shown on the inner drum. Fully insert the cable into
the inner drum.
Position the inner drum with cable into place. Carefully pull
the cable tip out and thread it into the slide action cable lock.
Place the slide action cable lock back on the drum before
letting go of the cable. Remove the protective cover on the
cable tip and tighten screws.
Children can fall into bucket and drown.
Keep children away from bucket with even a small amount
of liquid.
Read operator‘s manual. Use protective equipment.
Chemicals, bacteria and other substances that may cause
bums, be toxic or infectious may be present.
Use hot, soapy water to wash hands after handling.
Always use bucket insert to avoid damage to the drain cable
ONE-KEY™
To learn more about the ONE-KEY functionality for this tool,
please reference the Quick Start guide included with this
product or go to www.milwaukeetool.com/one-key. To
download the ONE-KEY app, visit the App Store or Google
Play from your smart device.
Also, when the product experiences ESD, the Bluetooth
communication will be disconnected. It needs to be reset
manually to recover.
We considered the results to be within our minimum
acceptable performance level according to EN 55014-2 / EN
301489-1 / EN 301489-17.
ONE-KEY™ Indicator
Solid Blue
Wireless mode is active and ready to be
con
fi
gured via the ONE-KEY™ app.
Blinking Blue
Tool is actively communicating with the
ONE-KEY™ app.
Blinking Red
Tool is in security lockout and can be
unlocked by the owner via the ONE-
KEY™ app.
EC-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole
responsibility that the product described under “Technical
Data” ful
fi
lls all the relevant regulations and the directives
2011/65/EU (RoHS), 2014/53/EU, 2006/42/EC, and the
following harmonized standards have been used:
EN 62841-1:2015
EN 62841-3-14:2017
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN 301 489-1 V2.2.3
EN 301 489-17 V3.1.1
EN 300 328 V2.2.2
EN IEC 63000:2018
Winnenden, 2021-02-03
Alexander Krug
Managing Director
Authorized to compile the technical
fi
le
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
GB-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole
responsibility that the product described under “Technical
Data” ful
fi
lls all the relevant provisions of the following
Regulations S.I. 2008/1597 (as amended), S.I. 2017/1206
(as amended), S.I. 2012/3032 (as amended) and that the
following designated standards have been used:
BS EN 62841-1:2015
BS EN 62841-3-14:2017
BS EN 55014-1:2017+A11:2020
BS EN 55014-2:2015
EN 301 489-1 V2.2.3
EN 301 489-17 V3.1.1
EN 300 328 V2.2.2
BS EN IEC 63000:2018
Winnenden, 2021-02-03
Alexander Krug
Managing Director
Authorized to compile the technical
fi
le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
MAINTENANCE
Greasing the cable feed
Keep all exposed, moving, and rotating parts cleaned
properly greased after each use. Grease the cable feed by
attaching a grease gun to the three zerk
fi
tting. Use grease
WHS 2002.
Oiling the cable feed bearings
1. Use a hose to clean out the cable feed with clean water
to remove contaminants. Drain the drum completely.
2. Move the cable feed handle to the left and apply
enough oil until the bearings rotate freely oil (WD40)
into the nose of the cable feed directly to the bearings.
3. Move the cable feed handle to the right and repeat.
4. Press the ratchet lever down and then feed and retract
the cable 30 - 60 cm multiple times to work the oil
around.
Cleaning Cables and Drums
The cable and drum should be thoroughly
fl
ushed with water
after every use to prevent damaging e
ff
ects of sediment and
drain cleaning compounds.
WARNING!
Wear leather gloves. After washing, dry the
cable and drum completely. Then, wipe cable with an oiled
rag before returning it to the drum according to the
instructions in "Cable Installation".
Warning, if the cable becomes bound up in the drum, the
cable will attack you
If the machine does not start or operate at full power with a
fully charged battery pack, clean the contacts on the battery
pack. If the machine still does not work properly, return the
machine, charger and battery pack, to a MILWAUKEE
service facility for repairs.
Use only Milwaukee accessories and spare parts. Should
components need to be replaced which have not been
described, please contact one of our Milwaukee service
agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the machine type printed as well as the six-digit
No. on the label and order the drawing at your local service
agents or directly at: Techtronic Industries GmbH,
Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any
work on the machine.
Содержание 4000474838
Страница 3: ...4 5 27 8 10 26 17 12 18 16 14 20 22 START STOP 19 ON OFF ...
Страница 8: ...14 15 1 4 2 3 60 max 559 mm 1 3 2 ...
Страница 9: ...16 17 OFF START STOP 1 1 2 ...
Страница 10: ...18 19 ...