manualshive.com logo in svg

MIHM-VOGT HTS-2/M/Zirkon-120, Руководство по эксплуатации

Поделиться
Скачать
MIHM-VOGT HTS-2/M/Zirkon-120 Скачать руководство пользователя страница 7

Safety

Version 5.0 - 10/2018

Operating Manual Sintering Oven HTS-2/M/Zirkon-120

Page 7

Safety

The 

sintering oven

 is a high-temperature oven for commercial use in dental 

laboratories and may only be used for sintering sinterable ceramics.

Requirements for personnel

Trained and qualified personnel who know how to use the unit 

and whose 

specialist training, skills, experience and knowledge of the relevant regula-
tions enables them to carry out the tasks assigned to them independently 
and recognise and avoid potential hazards.

Danger

Electricity!

Risk of death from electric shock.

 

h

Do not touch live cables and components with wet hands.

 

h

Observe the accident-prevention regulations when working with elec-

tric current.

 

h

Before carrying out any installation, maintenance, cleaning or repair 

work, disconnect the power supply of the 

sintering oven

 and secure it 

against being switched back on.

Danger

Risk of ignition!

Use of inflammable and explosive materials near the oven.

 

h

Do not operate the 

sintering oven

 near highly inflammable sources.

 

h

Do not install the 

sintering oven

 on highly inflammable supporting 

surfaces.

Содержание HTS-2/M/Zirkon-120



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды