manualshive.com logo in svg

MIHM-VOGT HTS-2/M/Zirkon-120, Руководство по эксплуатации

Поделиться
Скачать
MIHM-VOGT HTS-2/M/Zirkon-120 Скачать руководство пользователя страница 23

Initial commissioning

Version 5.0 - 10/2018

Operating Manual Sintering Oven HTS-2/M/Zirkon-120

Page 23

Sintering aids

Notice

Only use sintering aids approved by Mihm-Vogt.

You can find application notes in the information flyer for the relevant 

sintering aid.

Sintering process

Sintering OvenFeeding

 

$

The ceramic door panel is extremely porous and sensitive to scratch-
ing and impacts.

 

$

Do not grip the door panel with extraction pliers.

1. 

Switch the 

sintering oven

 on.

 

Â

The oven door opens automatically.

2. 

Fill the sintering dish (included in the delivery) with sintering granu-
late.

3. 

Place the item to be sintered in the sintering dish.

4. 

Place the equipped sintering dish on the support disc using suitable 
crucible tongs.

5. 

Start a firing program by pressing the 

Start/Stop

 button. 

 

Â

The oven door closes automatically.

Caution

Risk of crushing limbs!

The oven door closes automatically.

 

h

Only press the 

Start/Stop

 button after the filled sintering dish has 

been positioned.

 

h

Make sure that nobody reaches between the oven door and heating 

chamber while the oven door is closing.

Start

Stop

Содержание HTS-2/M/Zirkon-120



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды