Micronics 09-00232 Series Скачать руководство пользователя страница 60

Страница: 60 / 123

Micronics LPM30 System Board Manual

6-4

adding ADIACAD to your batch file.

Start AutoCAD and reconfigure it to use the enhanced display list driver.
For example, if you start AutoCAD using a batch file called
ACADR12.BAT, type:

ACADR1 -R <Enter>

The “-R” parameter is supported only by AutoCAD release. For other
releases, refer to your AutoCAD manuals.

Documentation for the DLXpress driver is provided on the installation
diskette. See the README.DLX file for details.

IBM OS/2 Presentation Manager 2.1

Installation Procedure

Perform the following steps to install driver using the IBM OS/2:

Start OS/2 2.1 to ensure it uses the Video Graphics Array (VGA) driver
before continuing with this procedure.

Insert the mach64 installation disk #1 into a floppy drive.

Open the DOS Full Screen icon.

The mach64 installation program does not run in a DOS window. The
DOS Box must be Full Screen for successful operation.

Do not switch out of Full Screen to run Diagnostic Tests. Doing so will
result in a corrupted display.

Type: A:\INSTALL <Enter> (For drive B, substitute B: for A:).

Select DRIVERS INSTALLATION from the Main Menu.

This will copy the mach64 driver to the MACH_OS2 directory.

Open an OS/2 Window or OS/2 Full Screen icon and type:

DPINSTL <Enter>.

Содержание 09-00232 Series




























































































































Результаты поиска

Содержание 09-00232 Series

Отзывы:

Бренды по названию

Популярные бренды

Micronics 09-00232 Series, Руководство пользователя

Результаты поиска

Содержание 09-00232 Series

Отзывы:

Бренды по названию

Популярные бренды