Micronics 09-00232 Series Скачать руководство пользователя страница 33

Страница: 33 / 123

Installing an ISA Peripheral Card

Micronics ISA slots accommodate all standard ISA peripherals. Complete the
following steps to install a ISA card:

Turn the computer system off and remove the cover.

Choose an unused ISA slot on the riser card and remove the slot cover.

Insert the card with the bottom edge level to the slot. Never insert the
card at an angle!

Carefully push the card straight in while securing the other side of the
riser card with your free hand. Make sure the card is fully inserted.

Replace the screw which holds the card into place.

Replace the cover.

Read the card’s manual for additional instructions concerning installation
and software drivers.

Figure 3-8 Installing an ISA Peripheral Card

3-11

Installing System Memory and Add-On Peripherals

Содержание 09-00232 Series




























































































































Результаты поиска

Содержание 09-00232 Series

Отзывы:

Бренды по названию

Популярные бренды

Micronics 09-00232 Series, Руководство пользователя

Результаты поиска

Содержание 09-00232 Series

Отзывы:

Бренды по названию

Популярные бренды