manualshive.com logo in svg

Micronics 09-00232 Series, Руководство пользователя

Поделиться
Скачать
Micronics 09-00232 Series Скачать руководство пользователя страница 51

5 - 5

Note:
It is recommended to accept the defaults suggested during installation.

1.

Select UTILITIES INSTALLATION from the Main Menu by using your
arrow keys to highlight it and press <Enter>.

2.

Enter the destination drive, directory, and press <Enter>.

3.

Enter the source drive and press <Enter>.

4.

Utilities are in the root directory of the Install Disk #1.  Accept the prompt
for the root directory and press <Enter> to start copying.

5.

When prompted for the boot drive, enter your boot drive (i.e., C) and
press <Enter>.

6.

To run the INSTALL program from any directory (in DOS), you must add
the location of the utilities to the PATH statement in the
AUTOEXEC.BAT file.  The default directory name used by this installa-
tion is C:\MACH64.

7.

When finished, press <Esc> and exit from the Main Menu.

8.

Changes made to the boot files (CONFIG.SYS and AUTOEXEC.BAT)
are active only if you reboot the computer.  If you encounter errors or
suspect the hard disk is full, refer to the Troubleshooting section in this
chapter or your DOS manual for information.

Diagnostics

From this menu, you can test the various operations and circuitry of the
mach64.  The diagnostics screen may be displayed at any supported resolution
and color depth for testing.  These tests support mouse and keyboard opera-
tions, and directions are displayed on the screen.  Errors found by testing are
discussed in the Troubleshooting section of this chapter.

Advanced Setup

The number of options in the Set Power-Up Configuration menu (see Figure
5-3) depends on the card type (i.e., ISA, VLB, or PCI).  To set up these
options, use the arrow keys to highlight ADVANCED SETUP and press
<Enter>, then set the options to match your monitor and system type.  If you
need help, press <F1>.

Installing Graphics Accelerator Software

Содержание 09-00232 Series




























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды