ENGLISH
en
7
power tool will do the job better and safer at the rate
for which it was designed.
b)
Do not use the power tool if the switch does
not turn it on and off.
Any power tool that cannot
be controlled with the switch is dangerous and must
be repaired.
c)
Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools.
Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d)
Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool.
Power tools are
dangerous in the hands of untrained users.
e)
Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition that
may affect the power tool's operation. If
damaged, have the power tool repaired before
use.
Many accidents are caused by poorly
maintained power tools.
f)
Keep cutting tools sharp and clean.
Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g)
Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed.
Use of the power tool
for operations different from those intended could
result in a hazardous situation.
2.5 Service
a)
Have your power tool serviced by a qualified
repair person using only identical replacement
parts.
This will ensure that the safety of the power
tool is maintained.
3.1 Safety Warnings Common for Grinding,
Sanding, Wire Brushing or Abrasive
Cutting-Off Operations:
a)
This power tool is intended to function as a
grinder, sander, wire brush or cut-off tool. Read
all safety warnings, instructions, illustrations
and specifications provided with this power
tool.
Failure to follow all instructions listed below
may result in electric shock, fire and/or serious
injury.WEVA 15-125 Quick can also be used as
polishing tool.
b)
Operations such as polishing are not
recommended to be performed with this power
tool.
Operations for which the power tool was not
designed may create a hazard and cause personal
injury. (Does not apply to WEVA 15-125 Quick.)
c)
Do not use accessories which are not
specifically designed and recommended by the
tool manufacturer.
Just because the accessory
can be attached to your power tool, it does not
assure safe operation.
d)
The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool.
Accessories running faster than
their rated speed can break and fly apart.
e)
The outside diameter and the thickness of
your accessory must be within the capacity
rating of your power tool.
Incorrectly sized
accessories cannot be adequately guarded or
controlled.
f)
Threaded mounting of accessories must
match the grinder spindle thread. For
accessories mounted by flanges, the arbour
hole of the accessory must fit the locating
diameter of the flange.
Accessories that do not
match the mounting hardware of the power tool will
run out of balance, vibrate excessively and may
cause loss of control.
g)
Do not use a damaged accessory. Before
each use inspect the accessory such as
abrasive wheels for chips and cracks, backing
pad for cracks, tear or excess wear, wire brush
for loose or cracked wires. If a power tool or
accessory is dropped, inspect for damage or
install an undamaged accessory. After
inspecting and installing an accessory,
position yourself and bystanders away from
the plane of the rotating accessory and run the
power tool at maximum no-load speed for one
minute.
Damaged accessories will normally break
apart during this test time.
h)
Wear personal protective equipment.
Depending on application, use face shield,
safety goggles or safety glasses. As
appropriate, wear dust mask, hearing
protectors, gloves and workshop apron
capable of stopping small abrasive or
workpiece fragments.
The eye protection must be
capable of stopping flying debris generated by
various operations. The dust mask or respirator
must be capable of filtering particles generated by
your operation. Prolonged exposure to high
intensity noise may cause hearing loss.
i)
Keep bystanders a safe distance away from
work area. Anyone entering the work area must
wear personal protective equipment.
Fragments
of workpiece or of a broken accessory may fly away
and cause injury beyond immediate area of
operation.
j)
Hold the power tool by insulated gripping
surfaces only, when performing an operation
where the cutting accessory may contact
hidden wiring or its own cord.
Cutting accessory
contacting a "live" wire may make exposed metal
parts of the power tool "live" and give the operator
an electric shock.
k)
Position the cord clear of the spinning
accessory.
If you lose control, the cord may be cut
or snagged and your hand or arm may be pulled into
the spinning accessory.
I)
Never lay the power tool down until the
accessory has come to a complete stop.
The
spinning accessory may grab the surface and pull
the power tool out of your control.
3. Special safety instructions
