Meridian SEED EXPRESS 240 RT Скачать руководство пользователя страница 56

Страница: 56 / 96

12. TROUBLESHOOTING

12.1 TROUBLESHOOTING CHART

PROBLEM

CAUSE

SOLUTION

Engine will not start.

No fuel.

Fill the fuel tank.

Low engine oil.

Fill the crankcase with oil.

Cold engine.

Open choke.

Ignition key switch off.

Turn ignition key switch on.

Battery dead.

Recharge or replace battery.

Engine problem.

Refer to engine manual.

Conveyor belt will not start.

No power.

Start engine and increase speed above

1400 RPM.

Drive motor coupling.

Repair or replace coupling.

Belt tension.

Increase belt tension.

No hydraulic oil.

Check oil level.

Electrical or hydraulic functions

are not working properly.

Transmitter power is OFF.

Turn Power ON.

Receiver power is OFF.

Turn Power ON.

Battery cable or battery.

Check battery cable and make sure battery

is fully charged.

Error in the control system.

Check LED Error Code light.

Improper ground.

Check for proper grounding electrical

circuit.

Hydraulic valve or motor.

Ensure hydraulic pump is working properly

andhydraulictankisfilledwithoil.

Intermittent function.

Check receiver antenna for damage and

proper connection.

Loose connector at the valve coil.

Weigh-Tronix display is not work-

ing when power is ON.

No input power.

Inspect the power cable for possible

damage.
Check the wiring connections for corrosion,

bent pins, or wire damage.

Incorrect Voltage.

The required Voltage is 10 to 17 Volts

with a negative ground. If the Voltage

is between 9 and 10 Volts, the indicator

will alternate between LOW.BAT and the

appropriate mode.

Dead battery.

Make sure the seed tenders 12 VDC

battery is fully charged and the output is 12

Volts.

Internal fuse.

Replace the 3.15 Amp fuse on the PC

board. Replace the fuse with Avery Weigh-

Tronixstylefuseorequivalent(AWTP/N

48561‑0190).Thefuseissoldereddirectly

to the main board and should be replaced

byacertifiedscaletechnician.

Check for incorrect connection to

the battery.

Connect BLACK wire to Ground and

WHITE wire to +12 VDC.

Weigh-Tronix display turns OFF

automatically.

Insufficientpower.

The indicator will automatically turn OFF if

the Voltage drops below 9 Volts for more

thanfiveseconds.

Содержание SEED EXPRESS 240 RT

































































































Результаты поиска

Содержание SEED EXPRESS 240 RT

Отзывы:

Похожие инструкции для SEED EXPRESS 240 RT

Бренды по названию

Популярные бренды

Meridian SEED EXPRESS 240 RT, Руководство оператора

Результаты поиска

Содержание SEED EXPRESS 240 RT

Отзывы:

Похожие инструкции для SEED EXPRESS 240 RT

Бренды по названию

Популярные бренды