Meridian SEED EXPRESS 240 RT Скачать руководство пользователя страница 29

Страница: 29 / 96

CONVEYOR STOP (4)

This button stops the conveyor belt.

CONVEYOR SPEED INC (5)

This button starts the conveyor belt. Press the

STOP button to stop conveyor.

CONVEYOR LEFT (6)

This button positions the conveyor to the left.

Press the LEFT button to position the conveyor

to the left side of the unit or the drivers side of the

tow vehicle.

CONVEYOR RIGHT (7)

This button positions the conveyor to the right.

Press the RIGHT button to position the conveyor

to the right side of the unit or the passenger’s side

of the tow vehicle.

CONVEYOR LIFT (8)

This button raises the conveyor.

CONVEYOR LOWER (9)

This button lowers the conveyor.

GATE 1 OPEN (10)

The Gate 1 OPEN button opens the slide gate at

the bottom of compartment 1. Press the OPEN

button to open the slide gate, and press Gate 1

CLOSEbutton(11)toclosetheslidegate.The

openingcanbevariedtoprovidethedesiredflow

rate of seed onto the conveyor belt.

GATE 1 CLOSE (11)

The Gate 1 CLOSE button closes the slide gate at

the bottom of compartment 1. Press the button to

close the slide gate. The opening can be varied

toprovidethedesiredflowrateofseedontothe

conveyor belt.

GATE 2 OPEN (12)

The Gate 2 OPEN button opens the slide gate at

the bottom of compartment 2. Press the OPEN

button to open the slide gate, and press Gate 2

CLOSEbutton(13)toclosetheslidegate.The

openingcanbevariedtoprovidethedesiredflow

rate of seed onto the conveyor belt.

GATE 2 CLOSE (13)

The Gate 2 CLOSE button closes the slide gate at

the bottom of compartment 2. Press the button to

close the slide gate. The opening can be varied

toprovidethedesiredflowrateofseedontothe

conveyor belt.

Содержание SEED EXPRESS 240 RT

































































































Результаты поиска

Содержание SEED EXPRESS 240 RT

Отзывы:

Похожие инструкции для SEED EXPRESS 240 RT

Бренды по названию

Популярные бренды

Meridian SEED EXPRESS 240 RT, Руководство оператора

Результаты поиска

Содержание SEED EXPRESS 240 RT

Отзывы:

Похожие инструкции для SEED EXPRESS 240 RT

Бренды по названию

Популярные бренды