Meridian SEED EXPRESS 240 RT Скачать руководство пользователя страница 48

Страница: 48 / 96

5. If the old belt cannot be used:

a. Remove the discharge hood and lower the

galvanized belt guards.

b. Install the new belt and connect the two

ends together.

6. Tighten the two drive drum adjusting bolts

equally to 23 ft-lbs. While holding the

adjusting bolt in place, retighten both locking

nuts.

7. Start the conveyor to make sure the belt is

tracking properly. If the belt is not tracking

properly, use the Belt Tracking Adjustment

procedure to correct the problem.

8. Recheck the tension and alignment of the

beltfrequentlyduringthefirsttenhoursof

operation and adjust, as needed.

NOTE:

Then, resume regular maintenance.

Typically,abeltwillseatitselfduringthefirstten

hours of operation and then require less or no

adjustment.

10.6 CHAIN DRIVE SYSTEM

The rotating platform chain should be periodically

maintained to ensure a long service life. Regularly

inspect the chain for potential problems and to

avoidprematurefailure.Earlyidentificationofa

problem is crucial to prevent costly downtimes.

1. The chain drive will operate successfully with

little or no lubrication beyond the initial factory

lubrication. However, periodic lubrication will

greatly extend the functional life of the chain

drive. The chain drive requires lubrication for

four purposes.

a. To resist wear of the pin-bushing joint.

b. To cushion impact loads.

c. To lubricate chain-sprocket contact

surfaces.

d. To retard rust or corrosion.

2. Lubricate the chain with a good grade of clean

petroleum oil without additives. The oil should

befreeflowingfortheambienttemperaturein

which the seed tender is operating.

Recommended Grade Temperature,

SAE 5

-50 to + 50

SAE 10

-20 to + 80

SAE 20

+10 to +110

SAE 30

+20 to +130

SAE 40

+30 to +140

SAE 50

+40 to +150

Содержание SEED EXPRESS 240 RT

































































































Результаты поиска

Содержание SEED EXPRESS 240 RT

Отзывы:

Похожие инструкции для SEED EXPRESS 240 RT

Бренды по названию

Популярные бренды

Meridian SEED EXPRESS 240 RT, Руководство оператора

Результаты поиска

Содержание SEED EXPRESS 240 RT

Отзывы:

Похожие инструкции для SEED EXPRESS 240 RT

Бренды по названию

Популярные бренды