Meridian SEED EXPRESS 240 RT Скачать руководство пользователя страница 53

Страница: 53 / 96

3. Check hydraulic motor to engine shaft

coupling and spider. Refer to the Changing

Hydraulic Motor Coupling section for

instructions.

4. Check turntable nylon slide blocks.

5. Thoroughly clean the seed tender.

6. Check the tires for wear, and replace if needed.

7. Make sure the rubber stop bumpers are

securely tightened and in place.

10.12 AXLE MAINTENANCE
10.12.1 First 200 Miles

1. Adjust brakes. Refer to OEM manual for

procedure.

10.12.2 3,000 Miles or 3 Months

1. Adjust brakes. Refer to OEM manual for

procedure.

2. Check torque on wheel nuts. Refer to the

section in this manual.

3. Inspect tires for wear. Refer to OEM manual

for procedure.

10.12.3 6,000 Miles or 6 Months

1. Inspect brake magnets for wear. Refer to

OEM manual for procedure.

2. Inspect suspension parts for wear. Refer to

OEM manual for procedure.

10.12.4 12,000 Miles or 12 Months

1. Inspect brake lining wear, check brake cylinder

for leaks, and inspect brake wiring for damage.

Refer to OEM manual for procedure.

2. Grease the wheel bearings and check the hub

for wear. Refer to OEM manual for procedure.

3. Inspect grease seal for leakage. Refer to

OEM manual for procedure.

4. Inspect springs for any wear or loss of arch.

Refer to OEM manual for procedure.

10.13 TIRES

Check the tires for normal and/or abnormal tire

wear. Replace tires that are damaged or worn

beyond normal tread life. Refer to the axle OEM

manual for a Tire Wear Diagnostic Chart.

Replace the tires with Meridian part number 18131

or an equivalent tire:

3T235/80R16

TR643

Load Range E

For Trailer Service Only

10.14 WELDING REPAIRS

Repair welding must be done with care

and with procedures that may be beyond

the capabilities of the ordinary welder.

Before performing any type of welding repair to the

seed tender, contact Meridian for approval.

WARNING

Personal Injury Hazard. Repairs or

modifications to the trailer, trailer

tongue, or trailer hitch can result in

serious injury or death should these repairs fail.

IMPORTANT NOTICE

Anyone performing a welding repair should be

certifiedinaccordancetotheAmericanWelding

Society(AWS)standards.

Содержание SEED EXPRESS 240 RT

































































































Результаты поиска

Содержание SEED EXPRESS 240 RT

Отзывы:

Похожие инструкции для SEED EXPRESS 240 RT

Бренды по названию

Популярные бренды

Meridian SEED EXPRESS 240 RT, Руководство оператора

Результаты поиска

Содержание SEED EXPRESS 240 RT

Отзывы:

Похожие инструкции для SEED EXPRESS 240 RT

Бренды по названию

Популярные бренды