Meridian SEED EXPRESS 240 RT Скачать руководство пользователя страница 45

Страница: 45 / 96

10.3.4 Clean Air Cleaner

Check and remove any debris from the foam

cover of the air cleaner daily before each usage.

Thoroughly clean or replace the foam cover every

threemonthsor50hoursofoperation(cleanit

morefrequentlywhenusedindustyconditions).

10.4 LOAD CELLS

Four load cells are used with the models equipped

with a weighing system. There is no maintenance

required for these load cells. If the seed tender

does not seem to be functioning correctly, refer

to the Troubleshooting section, call an authorized

dealer, or call the factory.

Note:

The load cells on the 240RT and 375RT

are contained within the frame of the seed tender.

This photo is for instructional purposes only and

does not represent the actual design of the seed

tender itself.

10.4.1 Wiring Connections to Scale

Box

All four load cells are connected to the scale box.

If the system is not working correctly, make sure

the wiring connections are securely attached to the

bottom of the scale box. If the problem continues,

contact Meridian.

Содержание SEED EXPRESS 240 RT

































































































Результаты поиска

Содержание SEED EXPRESS 240 RT

Отзывы:

Похожие инструкции для SEED EXPRESS 240 RT

Бренды по названию

Популярные бренды

Meridian SEED EXPRESS 240 RT, Руководство оператора

Результаты поиска

Содержание SEED EXPRESS 240 RT

Отзывы:

Похожие инструкции для SEED EXPRESS 240 RT

Бренды по названию

Популярные бренды