Meridian SEED EXPRESS 240 RT Скачать руководство пользователя страница 47

Страница: 47 / 96

10.5.3 Belt Tracking Adjustment

1. Loosen the locking nuts on the two adjusting

bolts.

2. Tighten or loosen the bolts on either side of

the discharge hood to correct the tracking

problem.

3. Using a wrench, hold the adjusting bolt in

place while tightening the locking nut against

the housing. Repeat this procedure for the

other adjusting bolt.

4. Start the conveyor and make sure the belt

is tracking in the center of the drive drum.

Readjust, if needed.

10.5.4 Belt Replacement

If the belt is unbroken, it may be possible to use

the old belt to thread the new belt into the delivery

tube.

1. Position the conveyor with easy access to

both ends.

2. Open the clean out door.

3. Position the lower drive drum adjusting bolts to

their loosest position.

4. If the old belt can be used to install the new

belt continue with this step; if not, continue to

Step 5.

a. Disconnect the two ends of the conveyor

belt. Attach the replacement belt to the

end of the old conveyor belt.

b. Slowly pull the old belt out of the delivery

tube and thread the new one into position.

c. Disconnect the old belt and connect the

ends of the new belt together.

Содержание SEED EXPRESS 240 RT

































































































Результаты поиска

Содержание SEED EXPRESS 240 RT

Отзывы:

Похожие инструкции для SEED EXPRESS 240 RT

Бренды по названию

Популярные бренды

Meridian SEED EXPRESS 240 RT, Руководство оператора

Результаты поиска

Содержание SEED EXPRESS 240 RT

Отзывы:

Похожие инструкции для SEED EXPRESS 240 RT

Бренды по названию

Популярные бренды